Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN User Manual Download Page 172 | Manualshive

Page: 172 / 330

background image

170

4 TROUBLESHOOTING
4.3 Checking the Network Status

When starting the CC-Link IE TSN/CC-Link IE Field diagnostics by specifying "Other Station (Single Network)"
or "Other Station (Co-existence Network)" in "Other Station Setting" on the "Specify Connection Destination
Connection" window, the following restrictions apply.
• A communication test cannot be used.
• A station information list cannot be used.
• If MELSECNET/H, multidrop connection of serial communication modules, an interface board for personal

computer, a GOT (FA transparent function used), or network modules of the MELSEC-Q/L series are
included in the communication path, diagnostics cannot start.

When "Other Station (Co-existence Network)" is specified in "Other Station Setting" on the "Specify
Connection Destination Connection" window and "CC-Link" or "C24" is specified in "Co-existence Network
Route", diagnostics cannot start.

When starting the CC-Link IE TSN/CC-Link IE Field diagnostics by specifying "Other Station (Single Network)"
or "Other Station (Co-existence Network)" in "Other Station Setting" on the "Specify Connection Destination
Connection" window, specify the network number and station number of the relay receiving station or relay
sending station for "Network No." and "Station No." in "Network Communication Route" on the "Specify
Connection Destination Connection" window.
For example, to start the CC-Link IE TSN/CC-Link IE Field diagnostics of the network number 2, specify the
network number 1 and station number 3, or the network number 2 and station number 0 in "Network No." and
"Station No.".

• Although the CC-Link IE TSN/CC-Link IE Field diagnostics of the network to which the relay sending station

belongs can be started, that of the network to which the relay receiving station belongs cannot be started.

• The CC-Link IE TSN/CC-Link IE Field diagnostics can be started for stations of up to eight networks ahead

(number of relay stations: 7) including the station directly connected to the engineering tool.

Station
No.0

Station
No.2

Station
No.3

Station
No.0

Station
No.1

Station
No.2

Station
No.3

Station
No.1

Station
No.1

Station
No.0

Station
No.3

Network No.1

Network No.3

Network No.2

Engineering tool

Sending
(relay) station

Receiving
(relay) station

Sending
(relay) station

Receiving
(relay) station

«
...
170
171
172
173
174
...
»

Summary of Contents for MELSEC iQ-R CC-Link IE TSN











































































































































































































































































































































Reviews:

No comments

Related manuals for MELSEC iQ-R CC-Link IE TSN

FPBA-01 PROFIBUS DP

Brand: ABB Pages: 2

ControlMaster CM15

Brand: ABB Pages: 4

615 Series ANSI

Brand: ABB Pages: 60

TLE Scalable 150

Brand: GE Pages: 6

Brand: GE Pages: 3

Brand: GE Pages: 80

PACSystems* RX3i

Brand: GE Pages: 39

PACSystems* RX3i

Brand: GE Pages: 35

PACSystems* RX3i

Brand: GE Pages: 3

PACSystems* RX3i

Brand: GE Pages: 169

PACSystems RX7i

Brand: GE Pages: 317

Brand: Panasonic Pages: 27

Brand: Panasonic Pages: 78

Brand: Panasonic Pages: 98

Brand: NAiS Pages: 173

Brand: Panasonic Pages: 2

Brand: Access Pages: 12

iBox Hub 25020180

Brand: Hans Grohe Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands