Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN User Manual Download Page 268 | Manualshive

Page: 268 / 330

background image

266

APPX
Appendix 3 Buffer Memory

Remote password lock status storage area

■

Remote password lock status system port (Un\G2102782, Un\G4199934)

[b0]: Auto-open UDP port
[b1]: MELSOFT transmission port (UDP/IP)
[b2]: MELSOFT transmission port (TCP/IP)
[b5]: SLMP transmission port (UDP/IP)
[b6]: SLMP transmission port (TCP/IP)
• 0: Unlocked/remote password not set
• 1: Lock status

Remote password function monitoring area

■

Auto-open UDP port continuous unlock failure count (Un\G2108800, Un\G4205952)

The mismatch count of remote password at unlock of the auto-open UDP port is stored. The count is cleared when the
password matches.
Range: 0 to 65535 (Values of 65535 or more are not changed)

■

MELSOFT transmission port (UDP/IP) continuous unlock failure count (Un\G2108801,

Un\G4205953)

The mismatch count of remote password at unlock of the MELSOFT transmission port (UDP/IP) is stored. The count is
cleared when the password matches.
Range: 0 to 65535 (Values of 65535 or more are not changed)

■

MELSOFT transmission port (TCP/IP) continuous unlock failure count (Un\G2108802,

Un\G4205954)

The mismatch count of remote password at unlock of the MELSOFT transmission port (TCP/IP) is stored. The count is
cleared when the password matches.
Range: 0 to 65535 (Values of 65535 or more are not changed)

■

SLMP transmission port (UDP/IP) continuous unlock failure count (Un\G2108805,

Un\G4205957)

The mismatch count of remote password at unlock of the SLMP transmission port (UDP/IP) is stored. The count is cleared
when the password matches.
Range: 0 to 65535 (Values of 65535 or more are not changed)

■

SLMP transmission port (TCP/IP) continuous unlock failure count (Un\G2108806,

Un\G4205958)

The mismatch count of remote password at unlock of the SLMP transmission port (TCP/IP) is stored. The count is cleared
when the password matches.
Range: 0 to 65535 (Values of 65535 or more are not changed)

Network type information area (Network type information)

■

Network type information area (Network type information) (Un\G2162687)

5: CC-Link IE TSN

«
...
266
267
268
269
270
...
»

Summary of Contents for MELSEC iQ-R CC-Link IE TSN











































































































































































































































































































































Reviews:

No comments

Related manuals for MELSEC iQ-R CC-Link IE TSN

Brand: ABB Pages: 139

Brand: ABB Pages: 28

Brand: ABB Pages: 59

Brand: B&G Pages: 2

Brand: B&K Pages: 9

Brand: FAAC Pages: 4

Brand: FAAC Pages: 52

Brand: Federal Signal Corporation Pages: 79

Brand: Federal Signal Corporation Pages: 32

Brand: Gardena Pages: 14

Brand: Gardena Pages: 4

GAT ACCESS 6100

Brand: Gantner Pages: 4

Brand: Harman Pages: 2

Brand: T-Link Pages: 3

Brand: WABCO Pages: 4

Brand: Rayrun Pages: 4

Brand: Parker Pages: 29

Brand: ZKTeco Pages: 43

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands