manualshive.com logo in svg

Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN, User Manual

Share
Download
Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN User Manual Download Page 117

2  PARAMETER SETTINGS

2.4  Application Settings

115

2

■

Setting 65 or more interlink transmission ranges

Use link direct devices in a program to perform interlink transmission.

■

Performing interlink transmission in a multiple CPU system

When different control CPUs are set for the network modules, interlink transmission cannot be performed using interlink 
transmission parameters or a program. Perform interlink transmission using data communication by the CPU buffer memory. 
(

 MELSEC iQ-R CPU Module User's Manual (Application))

Setting example

The following is a setting example to perform interlink transmission from the master station on CC-Link IE TSN to stations on 
CC-Link IE Controller Network. In this example, 128-point data input from the slave station (station No.1) is transferred.

RX200

RX

X

LB

RX27F

X1200

X127F

LB780

LB7FF

Master station 
(station No.0)

Copied with MOV instruction.

Network No.1

Network No.2

CPU module

Normal station 
(station No.4)

Station No.1 send 
range

Station No.2 send 
range
Station No.3 send 
range

Station No.4 send 
range

Link refresh

Ex.

Link direct device cannot be specified for both the first 
and second arguments. Specify CPU device by link 
refresh for either one.

RX200

RX

LB

RX27F

LB780

LB7FF

No.1

No.0

No.4

128

No.1

No.2

No.3

No.4

No.1

No.2

No.3

·

·

Summary of Contents for MELSEC iQ-R CC-Link IE TSN











































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands