Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN User Manual Download Page 262 | Manualshive

Page: 262 / 330

background image

260

APPX
Appendix 3 Buffer Memory

Protocol information

■

Protocol information (Un\G1294016 to Un\G1294031)

*1 Sets the protocol automatically according to the system settings.

While the system is operating with the protocol version 2.0, if a device that supports protocol version 1.0 attempts to join, the joining
station does not establish a data link.

Timeslot information for slave station cyclic transmission

■

Timeslot information for slave station cyclic transmission (Un\G1294048 to Un\G1294167)

Address

Name

Description

Un\G1294016

Protocol operating status

Stores the operating status of the protocol.
0: Operating protocol not determined or CC-Link IE TSN
Class settings set to CC-Link IE TSN Class B only
1: Operating with the protocol version 1.0
2: Operating with the protocol version 2.0

Un\G1294017

Write request

Write the protocol settings to RJ71GN11-T2.
0: Do not write
1: Write

Un\G1294018

Protocol setting

Set the operating protocol.
0: Automatic setting

1: Protocol version 1.0 fixed
2: Protocol version 2.0 fixed

Un\G1294019

Write implementation status

Stores the writing implementation status to RJ71GN11-T2.
0: Writing not implemented or in progress
1: Writing completed

Un\G1294020

Setting result

Stores the setting result.
0: Completed successfully
Other than 0: Completed with an error (error code)

Un\G1294021

Protocol setting status

Stores the protocol settings held by RJ71GN11-T2.
0: Automatic setting (factory default)
1: Protocol version 1.0 fixed
2: Protocol version 2.0 fixed

Un\G1294022 to Un\G1294031

System area



Firmware version

With/without connection to CC-Link IE TSN Class A devices

Operating protocol version

Protocol version 1.0

Protocol version 2.0

"15" or later

Available



1.0

Not available



2.0

"14"



Not available

1.0

Available

Available

1.0

Not available

Available

2.0

Address

Name

Description

Un\G1294048

Timeslot for station number 1 cyclic transmission

Stores the Timeslot for cyclic transmission of
station number 1.
0: Undetermined
1: Timeslot 1
3: Timeslot 3
4: Timeslot 4
5: Timeslot 5
6: Timeslot 6



Un\G1294167

Timeslot for station number 120 cyclic transmission

Stores the Timeslot for cyclic transmission of
station number 120.
0: Undetermined
1: Timeslot 1
3: Timeslot 3
4: Timeslot 4
5: Timeslot 5
6: Timeslot 6

«
...
260
261
262
263
264
...
»

Summary of Contents for MELSEC iQ-R CC-Link IE TSN











































































































































































































































































































































Reviews:

No comments

Related manuals for MELSEC iQ-R CC-Link IE TSN

Brand: GBD Pages: 12

Brand: Danfoss Pages: 2

Brand: Danfoss Pages: 2

Brand: Danfoss Pages: 12

Brand: Danfoss Pages: 24

Brand: Danfoss Pages: 60

Brand: Danfoss Pages: 10

Brand: Danfoss Pages: 20

Brand: Uclear Pages: 40

Brand: jablotron Pages: 22

Brand: jablotron Pages: 2

Brand: Koer Pages: 6

Brand: Universal Remote Pages: 20

Brand: Purmo Pages: 2

Brand: salmson Pages: 78

Brand: D+H Pages: 16

Brand: Bardiani Valvole Pages: 24

Brand: GE Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands