Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN User Manual Download Page 227

Page: 227 / 330

4 TROUBLESHOOTING

4.5 List of Error Codes

225

D2D0H

The station number specified for the
CCPASETX instruction is already in use.

• Execute the instruction again after correcting the station number in the

network configuration setting data to a unique value.

• If the error occurs again even after taking the above, please consult your

local Mitsubishi representative.



D2D1H

The link device range assignment specified
for each station in the CCPASETX
instruction is incorrect.

• Execute the instruction again after correcting the offset or the number of

points of link devices in the network configuration setting data.

• If the error occurs again even after taking the above, please consult your

local Mitsubishi representative.



D2D2H

The IP address/port number of the target
station is incorrect.

• Execute again after correcting the port number of the target station in the

setting data.

• If the error occurs again even after taking the above, please consult your

local Mitsubishi representative.



D2D3H

Send processing of the transient
transmission has failed.

• Check the network status using the CC-Link IE TSN/CC-Link IE Field

diagnostics of the engineering tool, and take action.

• When the own station, target station, or relay station detected an error,

identify the cause of the error and take action.

• Execute the instruction again after correcting the target IP address of

transient data.

• If the access destination is a module with a different network number,

correct the routing parameter setting.



D602H

Parameter error

• Write the network parameter to the CPU module again.
• If the error occurs again even after taking the above, please consult your

local Mitsubishi representative.



D605H

Parameter error

• Write the network parameter to the CPU module again.
• If the error occurs again even after taking the above, please consult your

local Mitsubishi representative.



D60BH

Parameter error (device overlap error (LB))

• Write the network parameter to the CPU module again.
• Execute the instruction again after correcting the offset or size of the link

device of the slave station in the setting data.

• If the error occurs again even after taking the above, please consult your

local Mitsubishi representative.



D60CH

Parameter error (device overlap error (LW))

• Write the network parameter to the CPU module again.
• Execute the instruction again after correcting the offset or size of the link

device of the slave station in the setting data.

• If the error occurs again even after taking the above, please consult your

local Mitsubishi representative.



D60DH

Parameter error (each station device range
assignment error (LB))

• Write the network parameter to the CPU module again.
• Execute the instruction again after correcting the size of the link device of

the slave station in the setting data.

• If the error occurs again even after taking the above, please consult your

local Mitsubishi representative.



D60EH

Parameter error (each station device range
assignment error (LB))

• Write the network parameter to the CPU module again.
• Execute the instruction again after correcting the offset of the link device

of the slave station in the setting data.

• If the error occurs again even after taking the above, please consult your

local Mitsubishi representative.



D60FH

Parameter error (each station device range
assignment error (LW))

• Write the network parameter to the CPU module again.
• Execute the instruction again after correcting the size of the link device of

the slave station in the setting data.

• If the error occurs again even after taking the above, please consult your

local Mitsubishi representative.



D610H

Parameter error (each station device range
assignment error (LW))

• Write the network parameter to the CPU module again.
• Execute the instruction again after correcting the offset of the link device

of the slave station in the setting data.

• If the error occurs again even after taking the above, please consult your

local Mitsubishi representative.



D611H

Parameter error (each station device range
assignment error (RWw))

• Write the network parameter to the CPU module again.
• Execute the instruction again after correcting the size of the link device of

the slave station in the setting data.

• If the error occurs again even after taking the above, please consult your

local Mitsubishi representative.



Error
code

Error definition and causes

Action

Detailed
information 1

Detailed
information 2

Summary of Contents for MELSEC iQ-R CC-Link IE TSN











































































































































































































































































































































Search results

Summary of Contents for MELSEC iQ-R CC-Link IE TSN

Reviews:

Brands by name

Popular brands

Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN, User Manual

Search results

Summary of Contents for MELSEC iQ-R CC-Link IE TSN

Reviews:

Brands by name

Popular brands