manualshive.com logo in svg

Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN, User Manual

The Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN is an advanced automation controller that ensures efficient and seamless communication within industrial systems. Unlock the full potential of this powerful device with our comprehensive user manual, available for free download from manualshive.com. Master this cutting-edge technology with ease.

Share
Download
background image

198

4  TROUBLESHOOTING
4.4  Troubleshooting by Symptom

Communications with Ethernet devices failed

When communications with Ethernet devices cannot be performed, check the following items.

For details on when communication using the engineering tool is not allowed in the settings of Windows Firewall, refer to the 
following.

 GX Works3 Operating Manual

If the above actions do not solve the problem, perform the module communication test to check for hardware failure. (

 

Page 168 Module Communication Test)

Although the data link is normal, communications for the link device failed

When the link device cannot communicate although the data link is normal (D LINK LED is on), check the following items.

Check item

Action

Is the firewall or proxy server setting enabled on the Ethernet device?

Check and correct the settings on the Ethernet device.
Is a response to the PING command (ICMP echo request) disabled?

Is the antivirus software on the Ethernet device blocking the 
communication?

Check and correct the antivirus software settings on the Ethernet device.

• Is the security setting level of the antivirus software low?
• Is a response to the PING command (ICMP echo request) disabled in the firewall 

settings?

In multicast mode, is a standard Ethernet device connected to the 
master station?

• Connect the standard Ethernet device to a local station or remote station that 

supports the multicast filter.

• Set unicast mode.
• Take actions so that the Ethernet device does not receive cyclic data in multicast 

mode.

In multicast mode, is a standard Ethernet device connected to a local 
station or remote station that does not support the multicast filter?

• Connect the standard Ethernet device to a local station or remote station that 

supports the multicast filter.

• Set unicast mode.
• Take actions so that the Ethernet device does not receive cyclic data in multicast 

mode.

In multicast mode, are a local station and an Ethernet device connected 
on the end side via a switching hub?

• Configure settings with the switching hub so that the multicast frame (with 

multicast MAC address 09:00:70:00:10:02 and 09:00:70:00:10:05) will not be 
transferred to the port of the standard Ethernet device.

• Check the connected device and do not connect both a local station and an 

Ethernet device on the end side of the switching hub.

• Set unicast mode.
• Take actions so that the Ethernet device does not receive cyclic data in multicast 

mode.

Check item

Action

Is "Reserved/Error Invalid Station" of the slave station set to "Reserved 
Station" in "Network Configuration Settings" of the master station?

Set "Reserved/Error Invalid Station" of the slave station to "No Setting".

Is the input/output bit setting or input/output word setting of the slave 
station set in "Network Configuration Settings" of the master station? 
(Simple display)

Set a link device used in the slave station correctly.

Are "RX Setting", "RY Setting", RWw Setting", "RWr Setting", "LB 
Setting", and "LW Setting" of the slave station set in "Network 
Configuration Settings" of the master station? (Detailed display)

Set a link device used in the slave station correctly.

Does the slave station support the link devices set in "Network 
Configuration Settings" of the master station?

Correct the link devices to be assigned to the slave station in "Network 
Configuration Settings" of the master station.

Is the link refresh setting range correct?

Correct the setting in "Refresh Settings" of "Basic Settings".

Is the refresh range of "CPU Side" in "Refresh Settings" overlapped with 
that of "CPU Side" of another network module?

Correct the setting in "Refresh Settings" of "Basic Settings".

Is the transfer range set in "Interlink Transmission Settings" correct?

Correct the transfer range set in "Interlink Transmission Settings".

Are the settings in "Transfer Source Module" and "Transfer Destination 
Module" of "Interlink Transmission Settings" correct?

Correct the settings in "Transfer Source Module" and "Transfer Destination Module" 
of "Interlink Transmission Settings".

When the local station cannot receive cyclic data from another station, is 
"Communication Mode" of the master station set to "Multicast"?

Set "Communication Mode" of the master station to "Multicast".

Summary of Contents for MELSEC iQ-R CC-Link IE TSN











































































































































































































































































































































Reviews:

No comments

Related manuals for MELSEC iQ-R CC-Link IE TSN

TCS Basys Controls QD Series Troubleshooting Worksheet preview
QD Series
Brand: TCS Basys Controls Pages: 2
Paradox Magellan REM2 Reference And Installation preview
Magellan REM2
Brand: Paradox Pages: 2
Koer C35CBMS Manual preview
C35CBMS
Brand: Koer Pages: 6
fadini ZERO.SAPE Manual preview
ZERO.SAPE
Brand: fadini Pages: 28
GEA VESTA Operating Instructions Manual preview
VESTA
Brand: GEA Pages: 47
Rain Bird EASY RAIN Manual preview
EASY RAIN
Brand: Rain Bird Pages: 11
4EVAC LOOPDRIVE FIM-RC Quick Start Manual preview
LOOPDRIVE FIM-RC
Brand: 4EVAC Pages: 2
Dantherm HRC 2 User Manual preview
HRC 2
Brand: Dantherm Pages: 28
Daikin BRC1H51W Installer And User Reference Manual preview
BRC1H51W
Brand: Daikin Pages: 32
C-TEC XFP502/X User Manual preview
XFP502/X
Brand: C-TEC Pages: 28
W.E.S.T. Elektronik POS-123-P-PFN Technical Documentation Manual preview
POS-123-P-PFN
Brand: W.E.S.T. Elektronik Pages: 53
Kelly KLS7250H User Manual preview
KLS7250H
Brand: Kelly Pages: 35
Unical Ufly P Installation And Servicing Manual preview
Ufly P
Brand: Unical Pages: 36
EasyCare toto User Manual preview
toto
Brand: EasyCare Pages: 26
Tescom RM2020 Installation And User Manual preview
RM2020
Brand: Tescom Pages: 15
CommBox Control Hub Quick Start Manual preview
Control Hub
Brand: CommBox Pages: 4
RDL RUC-4 Installation & Operation Manual preview
RUC-4
Brand: RDL Pages: 2
Invacare MK5 NX w/ACC Service Manual preview
MK5 NX w/ACC
Brand: Invacare Pages: 44

Brands by name

Popular brands

Load more brands