manualshive.com logo in svg

Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN, User Manual

The Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN is an advanced automation controller that ensures efficient and seamless communication within industrial systems. Unlock the full potential of this powerful device with our comprehensive user manual, available for free download from manualshive.com. Master this cutting-edge technology with ease.

Share
Download
background image

4  TROUBLESHOOTING

4.5  List of Error Codes

217

4

C06FH

The network number of request destination 
specified by the SLMP request message is 
not available for communications with the 
station number 121 or larger.

• If the 3E or 4E frame is used at SLMP, check that there is no error for the 

network number of the request destination and station number.

• If the station number extension frame is used at SLMP, check that there is 

no error for the network number of the request destination and station 
number.

C070H

The device memory cannot be extended for 
the access destination specified by the 
SLMP message.

• Correct the SLMP message to read/write data without the device memory 

set for extension.

• Specify the extension of the device memory only for the CC-Link IE TSN-

equipped module mounted station and R/Q/QnACPU via CC-Link IE 
Controller Network, MELSECNET/H, or MELSECNET/10.

C071H

The number of device points for data read/
write set for modules other than a MELSEC 
iQ-R/Q/QnACPU with the SLMP message is 
out of the range.

Correct the number of read/write points and send the SLMP message to the 
CC-Link IE TSN-equipped module again.

C072H

The request details of the SLMP message 
are incorrect. (For example, a request for 
data read/write in bit units has been issued 
to a word device.)

• Check if the data can be requested to the access destination.
• Correct the request details and send the SLMP message to the CC-Link 

IE TSN-equipped module again.

C073H

The access destination of the SLMP 
message cannot issue this request. (For 
example, the number of double word access 
points cannot be specified for modules other 
than a MELSEC iQ-R/Q/QnACPU.)

Correct the request details of the SLMP message.

C075H

The request data length for the label access 
is out of range.

• Correct the number of array points or number of read/write points and 

send the SLMP message to the CC-Link IE TSN-equipped module again.

• Correct the number of abbreviated points and send the SLMP message to 

the CC-Link IE TSN-equipped module again.

• Correct the label name length and send the SLMP message to the CC-

Link IE TSN-equipped module again.

• Shorten the label name and send the SLMP message to the CC-Link IE 

TSN-equipped module again.

• Correct the read/write data length and send the SLMP message to the 

CC-Link IE TSN-equipped module again.

C081H

The termination processing for the CC-Link 
IE TSN-equipped module that is involved 
with the reinitialization processing is being 
performed, and arrival of link dedicated 
instructions cannot be checked.

Finish all the communications to perform the reinitialization processing of 
the CC-Link IE TSN-equipped module.

C087H

IP address of the destination external device 
could not be acquired.

• Correct the IP address in the network station number 

 IP information 

setting.

• Check if the network or station number of the external device is correctly 

specified by using control data of the dedicated instruction.

• Check if the Ethernet cable is connected properly.

C0B2H

There is insufficient space in the receive 
buffer or the send buffer of the relay station 
or external station for the MELSOFT 
connection, link dedicated instructions, or 
SLMP. (Send 

 receive buffer full error)

Increase the request interval (execution interval) and execute the operation.

• Do not access through one station using the MELSOFT connection, link 

dedicated instruction, or SLMP.

• Wait for a response to the previous request before sending the next 

request.

• Correct the setting value of the timer setting for data communication of the 

CC-Link IE TSN-equipped module.

C0B3H

A request that cannot be processed was 
issued from the CPU module.

• Correct the request details.
• Correct the network number or request destination station number.

C0D4H

The number of relay stations to 
communicate with other networks exceeds 
the allowable range.

• Check if the specification (network number/station number) for the 

communication destination is correct.

• Check that the number of relay stations accessing the communication 

destination is 7 or less.

• Correct the settings in the network station number 

 IP information 

setting for the stations between the own station and the communication 
destination.

C0D8H

The number of specified blocks exceeded 
the range.

Correct the number of blocks.

C0D9H

The specified subcommand of the SLMP 
message is incorrect.

Correct the subcommand.

Error 
code

Error definition and causes

Action

Detailed 
information 1

Detailed 
information 2

Summary of Contents for MELSEC iQ-R CC-Link IE TSN











































































































































































































































































































































Reviews:

No comments

Related manuals for MELSEC iQ-R CC-Link IE TSN

Samson 3296 Mounting And Operating Instructions preview
3296
Brand: Samson Pages: 100
Danfoss JS120 Technical Information preview
JS120
Brand: Danfoss Pages: 16
Radio Shack Remote Control Owner'S Manual preview
Remote Control
Brand: Radio Shack Pages: 3
Unipulse F160 Operation Manual preview
F160
Brand: Unipulse Pages: 99
Accutrol VTS Installation & Operation Manual preview
VTS
Brand: Accutrol Pages: 25
Mainpine EPC Operating Instructions Manual preview
EPC
Brand: Mainpine Pages: 16
Danfoss AFP Series Installation Manual preview
AFP Series
Brand: Danfoss Pages: 20
Cabletron Systems SmartSwitch 6000 Installation & User Manual preview
SmartSwitch 6000
Brand: Cabletron Systems Pages: 76
Häfele 633.03.298 Quick Start Manual preview
633.03.298
Brand: Häfele Pages: 2
Häfele 633.03.298 Operating Instructions Manual preview
633.03.298
Brand: Häfele Pages: 24
IAI Msep First Step Manual preview
Msep
Brand: IAI Pages: 5
OBSIDIAN CONTROL SYSTEMS NX1 Installation Manual preview
NX1
Brand: OBSIDIAN CONTROL SYSTEMS Pages: 13
Rain Bird Image Series Quick Start Manual preview
Image Series
Brand: Rain Bird Pages: 4
Rain Bird ESP-ME3 Quick Reference Manual preview
ESP-ME3
Brand: Rain Bird Pages: 2
Rain Bird ESP-Me User Manual preview
ESP-Me
Brand: Rain Bird Pages: 140
Raindrip WeatherSmart RSC600i Installation & Programming preview
WeatherSmart RSC600i
Brand: Raindrip Pages: 36
Zeta Premier MX-16 Installation And Commissioning Manual preview
Premier MX-16
Brand: Zeta Pages: 44
Petique JG01500103 Instruction Manual preview
JG01500103
Brand: Petique Pages: 44

Brands by name

Popular brands

Load more brands