manualshive.com logo in svg

Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN, User Manual

Share
Download
Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN User Manual Download Page 187

4  TROUBLESHOOTING

4.4  Troubleshooting by Symptom

185

4

When "Connection 
Device Information" 
under "Basic Settings" 
of the master station is 
set to "Mixture of CC-
Link IE TSN Class B/A 
or CC-Link IE TSN 
Class A Only"

■

For firmware version "13" or earlier

Are nine or more CC-Link IE TSN Class B devices 
and TSN hubs connected in total to each port of 
the master station in the transmission path from the 
master station to the CC-Link IE TSN Class B 
device of the end?

Check the connected device and reduce the number of CC-Link IE TSN Class 
B devices and TSN hubs to eight or less in total for each port of the master 
station in the transmission path from the master station to the CC-Link IE TSN 
Class B device of the end.

Is the CC-Link IE TSN Class B device other than 
the master station connected in a star topology via 
a general-purpose hub?

• Other than the master station, do not connect CC-Link IE TSN Class B 

devices to a general-purpose hub in the star topology.

• Connect CC-Link IE TSN Class B devices to a TSN hub.

Is the master station connected with CC-Link IE 
TSN Class B devices via a general-purpose hub?

• Check the connected device and connect the master station to CC-Link IE 

TSN Class B devices in a line topology without using a general-purpose 
hub.

• Check the connected device and connect the master station and CC-Link IE 

TSN Class B devices to a TSN hub.

■

For firmware version "13" or earlier

In multicast mode, is the CC-Link IE TSN Class A 
remote station connected to the master station?

• Connect the local station or remote station supporting the multicast filter to 

the CC-Link IE TSN Class A remote station.

• Set unicast mode.

In multicast mode, is the CC-Link IE TSN Class A 
remote station connected to a local station or 
remote station that does not support the multicast 
filter?

In multicast mode, are a local station and a CC-
Link IE TSN Class A remote station connected on 
the end side via a switching hub?

• Configure settings with the switching hub so that the multicast frame (with 

multicast MAC address 09:00:70:00:10:02 and 09:00:70:00:10:05) will not 
be transferred to the port of the CC-Link IE TSN Class A remote station.

• Check the connected device and do not connect both a local station and a 

CC-Link IE TSN Class A remote station on the end side of the switching 
hub.

• Set unicast mode.

Is an Ethernet device connected to places other 
than the end of the network?

Check the connected device and connect the Ethernet device at the end of the 
network.

Does the connected switching hub support the CC-
Link IE TSN Class used?

Use the switching hubs that support "CC-Link IE TSN Class Setting" set to the 
master station. For the models and usage methods of the switching hubs, 
refer to the CC-Link Partner Association website (www.cc-link.org).

■

For firmware version "14" or later

Is the event code 00C81 registered in the event 
history?

Change "CC-Link IE TSN Class Setting" under "Network Configuration 
Settings" or "CC-Link IE TSN Class" on the slave station side so that the CC-
Link IE TSN Class settings for each station match.

If the slave stations being used support protocol 
version 2.0, is an master station that does not 
support protocol version 2.0 being used?

Update the master station to a firmware version that supports protocol version 
2.0. Alternatively, replace with a master station that supports protocol version 
2.0.

Check item

Action

Summary of Contents for MELSEC iQ-R CC-Link IE TSN











































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands