manualshive.com logo in svg

Lucent Technologies 5ESS-2000, Operations And Maintenance Procedures, Page: 33 / 1421

Share
Download
Lucent Technologies 5ESS-2000 Operations And Maintenance Procedures Download Page 33

Interface (EAI) commands. The SCC and MCC terminals support terminal-level authority checking only. Authority
checking is not supported on 

UNIX

®

 terminals.

3.8.3  AUTHORITY CHECKING CONCEPTS

3.8.3.1  Command Groups

3.8.3.1.1  General

A command group is a set of input messages and command pokes grouped together because they share a
common function, operate on a common unit, or have some other common characteristics. Each input message
and poke is a member of exactly one command group. Command groups are assigned to users and devices to
define the set of permissible commands. Example command groups include NMOC (Network Management and
Overload Control), SM (Switching Module Maintenance), and ALARM (Alarm Manipulation).

A complete table of command group names and explanations is located in the Introduction section of 235-600-700,

5ESS

®

-2000 Switch Input Messages Manual

.

The Command Group Index, an alphabetically-ordered list of input message identifiers and their command groups,
is located in the Indexes section of 235-600-700, 

5ESS

®

-2000 Switch Input Messages Manual

.

The Command Group Appendix, which maps commands groups to input message identifiers, is located in the
Appendixes section of 235-600-700, 

5ESS

®

-2000 Switch Input Messages Manual

.

In addition, each input message in the 235-600-700, 

5ESS

®

-2000 Switch Input Messages Manual

 specifies its own

command group or groups.

3.8.3.1.2  Special Command Groups

Two special command groups, NOCHK and SUPERUSR, are defined to bypass authority checking for two different
purposes.

NOCHK Command Group: 

 The NOCHK command group contains input messages that are never authority

checked. For example, 

OP:CLK

, a popular input message that presents no danger to the system, is in the NOCHK

command group.

All users and terminals are implicitly permitted to execute NOCHK commands. Thus, the system administrator can
not assign the NOCHK command group to users or terminals. CMDLOG logfile entries are never created for
NOCHK commands. Furthermore, CMDLOG logging and reporting is not configurable for the NOCHK command
group.

SUPERUSR Command Group: 

 The SUPERUSR command group does not actually contain any input messages

or pokes. It is a keyword that, when assigned to a user, instructs the system to by-pass terminal restrictions.
Judicious use of SUPERUSR is advised for security reasons.

3.8.3.1.3  Command Profiles

To simplify assignment of command groups to users and terminals, the administrator may define one or more
command 

profiles

, which are simply lists of command groups. Command profiles are assigned to users or terminals

similar to the way command groups are assigned.

3.8.3.2  Levels of Authority Checking

3.8.3.2.1  General

235-105-210

October 1999

Copyright © 1999

Page 22

Summary of Contents for 5ESS-2000














































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments