manualshive.com logo in svg

Lucent Technologies 5ESS-2000, Operations And Maintenance Procedures, Page: 116 / 1421

Share
Download
Lucent Technologies 5ESS-2000 Operations And Maintenance Procedures Download Page 116

temporary disk file is thrown away, and the system boots from the official file, effectively backing out the update(s).

When a temporary update is made permanent, an updated version of the file is built in the same directory as the
original version. A windowless move then takes place to effectively make the new version official. The in-core
memory is not touched when an update is made official since the update has already been installed there.

The software updates can also be activated by maintenance personnel at the SCCS or MCC by printing the
message file of the applicable software updates and manually installing the required messages.

5.3.4.5  Backout

During the soak interval, the temporary software update is observed to ensure proper performance. If the software
update does not perform properly at any time during the soak interval, it should be backed out using the

UPD:EXEC:CMD:BKOUT;

 message. The BACKOUT section backs out the designated change, plus any

subsequently installed temporary changes; that is, the backout process can only delete changes in the exact reverse
order of application. A sequential list of changes that are in the temporary state may be obtained using the

UPD:DISPLAY;TEMP;

 message.

5.4  EMERGENCY FIX

5.4.1  GENERAL

Regular program updates are performed in a timely and orderly fashion through software updates. Unexpected
problems with the software release can occur that require immediate correction, not allowing time for the normal
software update development and issue processes. These immediate corrections are known as emergency fixes.
Emergency fixes are accomplished on a word-by-word basis under the direction of Lucent Technologies Customer
Technical Support (CTS) [formerly Product Engineering Control Center (PECC)].

Emergency fixes are assigned a sequential craft number similar to the software update number. The program
update subsystem provides emergency fixes with the same status and processes as software updates (that is,
make temporary, backout, make permanent). Emergency fixes specify the address to be changed, the new data to
be inserted, and the old data to be matched. Emergency fixes are also known as address-data couplets.

5.4.2  SCCS AND MCC INTERFACE

As with software updates, most emergency fixes are activated remotely by the SCCS. Communication between the
SCCS and the program update subsystem is via the maintenance channel. The local office can be unattended
during the activation of the fix. Emergency fixes may also be activated locally through the MCC.

5.4.3  GENERAL FORMAT FOR EMERGENCY FIX ACTIVATION

5.4.3.1  Activation

The 

LOAD:UPNM....;

 message causes a temporary change to be made at the specified location. After a suitable

test and soak period, the 

UPD:UPNM....;OFC;

 message makes the change permanent, and normal backout

procedures can no longer be used.

5.4.3.2  Backout

Normal backout can be accomplished only while the fix is in a temporary state. The backout procedure can be
implemented using the 

UPD:BKOUT:UPNM;

 message. This message backs out the designated change, plus any

subsequently installed changes, because the backout process can only delete changes in the exact reverse order of
application. The

 UPD:DISPLAY:TEMP;

 message provides a sequential list of changes that are in a temporary state.

235-105-210

October 1999

Copyright © 1999

Page 8

Summary of Contents for 5ESS-2000














































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments