LG-Nortel IP LDK-20 Programming Manual Download Page 541

Page: 541 / 581

IP LDK-20 Programming Manual Quick

ADMIN Programming table

525

PGM FLEX

ITEM

RANGE

DEFAULT

REMARK

System Attributes-II

1-18

Network Time/Date Setting

ON / OFF

OFF

If this value is set to ON, the system time/date

are set by the network time/date.

Off-Hook Ring Signal Type

MUTE / BURST

MUTE

The off-hook ring type in the system can be set

to mute or one burst ring.

Override 1st CO Line Group

ON / OFF

If this value is set to ON, if there is no available

CO Line in the first CO Line Group, system can

access the next accessible CO Line Group.

Page Warning Tone

ON / OFF

If this value is set to ON, page warning tone will

be heard when paging starts.

Auto Privacy

ON / OFF

If this value is set to ON, the call is protected

from override regardless of Station Override

Privilege (ADMIN 113-FLEX 4).

Privacy Warning Tone

ON / OFF

If this value is set to ON, privacy warning tone

will be heard when the call is overridden.

Single Ring for CO Call

YES / NO

The cadence of ICM ring is set to 1sec on/

4sec off.

The cadence of CO ring is set to 0.4s on/ 0.2s

off/ 0.4s on/ 4sec off.

If this value is set to YES, the ICM ring

cadence and the CO ring cadence is reversed

each other.

WTU Auto Release

ON / OFF

OFF

If this value is set to ON, WTU is released

automatically.

ACD Print Enable

ON / OFF

OFF

If this value is set to ON, ACD Print is

available.

ACD Print Timer

001 – 255

(3 digits)

001

ACD database is printed per desired time

interval.(10 sec or 1 hour based : ADMIN 161-

FLEX 14)

ACD clear Database after

ON / OFF

OFF

If this value is set to ON, ACD database is

initialized after printed out.

VMIB PROMPT GAIN

00 - 31

This value is gain of VMIB

Announcement(Prompt). Whenever VMIB

Announcement is played, this value is applied.

CLI Information of VM SMDI

ON / OFF

OFF

If this value is set to ON, CLI is added when

Voice Mail information is printed through

RS232 port by SMDI.

ACD Print Timer Unit

HOUR / SEC

SEC

This value determines the unit of ACD Print

timer(ADMIN 161 - FLEX 10).

(1 hour or 10 seconds)

Set VM SMDI Type

TYPE II / TYPE I

TYPE I

This value sets VM SMDI type.

Incoming Toll Check

ON / OFF

OFF

If this value is set to ON, the system checks toll

of incoming CO call.

161

Auto FAX Transfer CO

1 - 8

The programmed CO line will be used for

automatic FAX transfer.

Summary of Contents for IP LDK-20






































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for IP LDK-20

Reviews:

Related manuals for IP LDK-20

Brands by name

Popular brands

LG-Nortel IP LDK-20, Programming Manual

Search results

Summary of Contents for IP LDK-20

Reviews:

Related manuals for IP LDK-20

Brands by name

Popular brands