IP LDK-20 Programming Manual Quick
ADMIN Programming table
534
PGM FLEX
ITEM
RANGE
DEFAULT
REMARK
1
SLT Hook Switch Bounce
Timer
01 – 25
(2 digits)
01
(100ms)
This timer is used at SLT only. Select the length
of time that is needed to regard as a valid on-
hook or off-hook (for SLT).
2
SLT Maximum Hook Flash
Timer
001-250
(3 digits)
06
(10ms)
This timer is used at SLT only. Select how long
the user could press the hook switch in order
for it to be considered a FLASH (Timed-Break
Recall) (for SLT).
3
SLT Minimum Hook Flash
Timer
000 – 250
(3 digits)
020
(100ms)
This timer is used at SLT only. The minimum
bound time that system considers as hook flash
for SLT.
4
SLT Ring Phase Timer
2 – 5
(1 digit)
4
(sec)
Select the ring phase(cadency) of SLT.
(5 SEC: 1SEC ON / 4SEC OFF)
5
Station Auto Release Timer
020 – 300
(3 digits)
060
(sec)
If a station hears ring back tone and no action
is taken, this timer is assigned. When this timer
is expired, the station is released.
6
Unsupervised Conference
Timer
00 – 99
(2 digits)
10
(min)
Select the amount of the time that an
unsupervised conference can continue after the
initiator of the conference has exited the
conference.
7
Wake-Up Fail Ring Timer
00 – 99
(2 digits)
20
(sec)
After a Wake-up fail ring invokes on system
attendant, the alarm ring exists during this
timer. If this
timer expires, the alarm ring will be
disappeared.
8
Warm Line Timer
01 – 20
(2 digits)
05
(sec)
User takes no action after lifting handset or
pressing the
[MON]
button and this timer is
expired, then idle line selection for warm line is
executed.
9
Wink Timer
010 – 200
(3 digits)
010
(10ms)
The time duration of seize acknowledge signal
to DID line.
10
Enblock Digit timer
01-20
(2 digits)
15
(sec)
This timer is used at the enblock dialing
sending feature. If station user make a call at
the enblock dialing mode, and if station user
doesn’t dial within this time, then the enblock
dialing is executed.
11
CCR Time Out Timer
000-300
(3 digits)
015
(sec)
When this timer is expired, CCR is activated.
12
DID Inter Digit Timer
01-20
(2 digits)
03
(sec)
This timer is used at DID type 2 feature. In DID
type2, IP LDK system will be wait the new DID
digit receiving until this timer is expired. If this
timer is expired, the call routing of DID type 2 is
executed.
13
FAX Tone Detect Timer
01 – 10
(2 digits)
05
(sec)
FAX tone detection is tried until this timer
expires.
182
14
FAX CO Call Timer
1 – 5
1
(min)
This timer sets the maximum call duration of a
FAX call.
CIDU Setting
1
CIDU USAGE
ON / OFF
ON
If this value is set to ON, CIDU can be served
2
CID Name Display
NAME(1)/
TEL NO(0)
TEL NO(0)
According to this ADMIN program value, LCD
displayed data can be selected.
3
Serial Port Select
1-4
-
Not available in IP LDK-20
4
CID/ Co Port Mapping
000-063
-
Not available in IP LDK-20
5
Initialize CID Data
6
CID Type2 Usage
ON/OFF
OFF
185
7
Fast CID Mode
ON/OFF
OFF
If this value is set to ON, system provides a
ring signal to SLT and CID will be displayed
after 1
st
ringing.
Summary of Contents for IP LDK-20
