LG-Nortel IP LDK-20 Programming Manual Download Page 225 | Manualshive

Page: 225 / 581

background image

IP LDK-20 Programming Manual System Feature

209

2.16.14 Message Waiting Indication (MWI)

Description

The  MWI(Message  Waiting  Indication)  is  the  exactly  same  service  as  the  CLI(Calling  Line
Identification) message wait that is described at Section 2.14.2(see Ref.1)
A  station  can  leave  the  CLI  message  of  itself,  when  the  station  of  other  networking  system  doesn’t
answer.  In  this  case,  at  the  system  of  unanswered  station  located,  the  ADMIN  program  of  CLI
message wait(PGM114 – FLEX 4) must be enabled. MWI is indicated by CLI message on station LCD.

Operation

To retrieve MWI message

1. Press the flashing

[CALLBK]

button.

2. MWI contents (CLI number, date and time, the calling count from the same CLI) will be shown

on LCD.

3. Press the volume up/down [

56

] button. The previous MWI or the next MWI is displayed.

To delete the current CLI Message and see the next one

1. Press

[CONF]

button.

2. Current MWI message is cleared with a confirmation tone and the next MWI message is

displayed.

To make a call back

1. Retrieve MWI with pressing the flashing

[CALLBK]

button and the volume up/down

[

56

]

button.

2. Press

[HOLD]

button.

3. Then system makes a net call according to MWI data.

Condition

1. MWI is applied to LCD panel installed station only.

2. When system makes a call back according to MWI data, the CO line is selected within the

network CO group.

Reference

1. CLI Message Wait : Section 2.14.2

Admin Programming

■

CLI Message Wait

4.1.5.4 (PGM114 – FLEX 4)

■

Networking Basic Attribute

4.11.1 (PGM 320)

■

Networking CO Line Attribute

4.11.3 (PGM 322)

■

Network Routing Table(Numbering Plan)

4.11.4 (PGM 324)

«
...
223
224
225
226
227
...
»

Summary of Contents for IP LDK-20






































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IP LDK-20

Brand: Panasonic Pages: 726

Brand: Panasonic Pages: 6

Brand: Panasonic Pages: 16

Brand: Panasonic Pages: 86

Brand: Panasonic Pages: 96

Brand: Panasonic Pages: 132

Brand: Panasonic Pages: 133

Brand: Panasonic Pages: 159

Brand: Panasonic Pages: 150

Brand: Panasonic Pages: 158

Brand: Panasonic Pages: 164

Brand: Panasonic Pages: 192

Brand: Panasonic Pages: 238

Brand: Panasonic Pages: 420

coovox-U50 series

Brand: Zycoo Pages: 14

Brand: Panasonic Pages: 204

OpenCom 100 series

Brand: Aastra Pages: 256

Quadro Quadro 4xi

Brand: Epygi Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands