LG-Nortel IP LDK-20 Programming Manual Download Page 18

Page: 18 / 581

IP LDK-20 Programming Manual Abbreviation and Keywords Table

Abbreviation / Keywords

Full Spelling

Description

BGM

Back Ground Music

The software service of providing BGM through the station speaker.

BLF

Busy Lamp Field

The software service of presentation of the network station status via button LED.

BRI

Basic Rate Interface

ISDN BRI CO line.

BRIB

Basic Rate Interface Board

BRI CO line board for IP LDK.

FLEX

Button

The Abbreviated presentation of 'button'.

Call Back

The software service that the caller can leave a message to unanswered station,
and the station user can check the leaved message.

Call Park

The software service that hold a call to retrieve by any other station.

Called Party

The opposite side of the caller.

Calling Party

The caller.

Camp On

The software service of indicating the another call waiting signal.

CAPI

Common ISDN Application
Programming Interface

ISDN protocol.

CAS

Centralized Attendant Service

The software service of attendant call on network connection.

CCBS

Completion of Call to Busy Subscriber The call back service protocol of QSIG and H.450.

CCNR

Completion of Call to No Reply

The call back service protocol of QSIG and H.450.

CCR

Customer Call Routing

The software service of CO incoming call via multi-level VMIB announcement.

CFW

Call Forward

The Abbreviated presentation of 'call forward'.

CID

Caller ID

The analog CO line caller ID.

CIDU

Caller ID Unit

IP LDK board to serve the analog CO line caller ID.

Circular Group

The call distribution method of hunt group.

CLI

Calling Line Identification

The telephone number of the caller.

CLIP

Calling Line Identification Presentation The software service of CLI display.

CLIR

Calling Line Identification Restriction

Prohibit the transmission of CLI.

CMU

Call Metering Unit

IP LDK hardware board to detects call metering signals from CO line.

CO Group or CO GRP or CO Line Group

Central Office Line Group

The truck line group of analog, ISDN, IP, etc.

CO or COL or CO Line

Central Office Line

The truck line of analog, ISDN, IP, etc.

Summary of Contents for IP LDK-20






































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for IP LDK-20

Reviews:

Related manuals for IP LDK-20

Brands by name

Popular brands

LG-Nortel IP LDK-20, Programming Manual

Search results

Summary of Contents for IP LDK-20

Reviews:

Related manuals for IP LDK-20

Brands by name

Popular brands