LG-Nortel IP LDK-20 Programming Manual Download Page 568

Page: 568 / 581

IP LDK-20 Programming Manual Quick

ADMIN Programming table

552

5.3.23 NETWORKING ATTRIBUTE

PGM FLEX

ITEM

RANGE

DEFAULT

REMARK

Networking Basic Attributes

F1-F7

Networking Enable

ON / OFF

OFF

This ADMIN program value is used to enable the

networking feature.

To set this ADMIN value to ON, the networking

software lock-key must be installed at IP LDK

system.

If station user enter the software lock-key check

dialing command ‘

[TRANS/PGM]

+ 78’, then the

installed software lock-key is displayed on station

LCD.

Networking Retry Count

00 – 99

This ADMIN value is used to retry the connection

when IP LDK system detect the error during

networking connection signaling. This value is

only used when the networking feature is

executed through the public switching network.

This value is not used at the networking feature

between direct connected IP LDK systems.

Networking CNIP Enable

ON / OFF

The name of calling station is sent to the called

system between IP LDK systems. CNIP is

displayed on called party station LCD according

to ADMIN programming. If the CNIP and CLI are

received together, CNIP is prior to CLI.

Networking CONP Enable

ON / OFF

OFF

The name of answered station is sent to the

calling system between IP LDK systems. CONP

is displayed on calling party station LCD

according to ADMIN programming.

Networking Signal Method

FAC / UUS

FAC

Select the information element type for

networking supplementary service message.

FACILITY/USER-TO-USER information element

can be used for networking supplementary

service message.

Networking CAS Enable

ON / OFF

OFF

The networking CAS is explained at Section

2.16.16.

Enable Centralized attendant in master system,

CAS should be disabled.

Networking VPN Enable

ON / OFF

OFF

Reserved

320

NET CC Retain Mode

ON / OFF

OFF

This value is used to set the networking

supplementary signaling type of the call

completion.

If this value is set to ON, the signaling of call

completion retain mode is executed.

Summary of Contents for IP LDK-20






































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for IP LDK-20

Reviews:

Related manuals for IP LDK-20

Brands by name

Popular brands

LG-Nortel IP LDK-20, Programming Manual

Search results

Summary of Contents for IP LDK-20

Reviews:

Related manuals for IP LDK-20

Brands by name

Popular brands