LG-Nortel IP LDK-20 Programming Manual Download Page 32 | Manualshive

Page: 32 / 581

background image

IP LDK-20 Programming Manual System Feature

16

2.1.4 DISA(Direct Inward System Access)

Description

This feature allows CO incoming calls to access to specific destination without attendant’s answering.
Compared with DID(see Ref.1), there is no digit conversion in DISA.
On seizing incoming CO Line, system gives VMIB announcement(see Ref.2) or dial tone. Then the
caller dials additional digit to access desired destination.

Operation

DISA Line Assignment

1.

[TRANS/PGM]

+ 140

2. Enter the CO Line range to be assigned to DISA Line.
3.

[FLEX 2]

+ Ring type +

[FLEX 1]

+ ‘1’ +

[HOLD/SAVE]

: DISA Activate.

- Ring type : FLEX 1-Day, FLEX 2-Night, FLEX 3-Weekend, FLEX 4-On-demand.

4.

[FLEX 2]

+ Ring type +

[FLEX 2]

+ ‘01~70’ +

[HOLD/SAVE]

: VMIB Greeting Assign.

To use DISA,

1. Seize the DISA Line of the system.
2. When the tone or announcement is heard, dial the desired station/ hunt group number then the

station/hunt group receives the call .

3. After connected with the system, user can dial the CO Access Code(e.g : 8801) to call outside of

the system again by seizing another CO Line.

Condition

1. You can assign VMIB announcement instead of intercom dial tone for DISA line.
2. If the DISA Authorization Code is enabled for a DISA Line, DND warning tone or VMIB

announcement, guiding to enter DISA Authorization Code, is heard and the Authorization
Code(see Ref.3) should be entered. And the dial tone will be heard.

3. Each DISA Line may be assigned as a full-time DISA or night mode only. Night mode DISA

operates as normal CO Line in the Day mode.

4. If the VMIB announcement number is stored with “#”, the CO Line will be dropped after the VMIB

announcement is played.

5. If the DISA Authorization Code is enabled for a DISA CO Line, the user should enter DISA

Authorization Code to access the CO Line.

6. If the DISA Authorization Code is disabled, the permission is determined by “CO to CO COS” &

“CO COS” (see Ref.4).

7. If the DISA Authorization Code is enabled, the Authorization Code should be entered to access

outgoing CO Line. If the Authorization Code is matched with the Authorization Code of station,
the user may access the CO Line depending on “STA COS” & “CO COS”. If the Authorization
Code is matched with the Authorization Code of system, it is determined by “CO to CO COS” and
“CO COS”.

Reference

1.    DID : 2.1.3
2.    VMIB announcement : 2.11
3.    Authorization Code : 2.5.2
4.    COS : 2.5.4

«
...
30
31
32
33
34
...
»

Summary of Contents for IP LDK-20






































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IP LDK-20

Brand: Solwise Pages: 7

Brand: Connexity Pages: 224

Brand: Panasonic Pages: 191

Brand: SpectraLink Pages: 89

Brand: Xorcom Pages: 6

Brand: Panasonic Pages: 92

Brand: Synway Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands