Kongsberg Simrad SN90, Installation Manual

Page: 290 / 298

288
381298/C
connecting external devices to the Processor
Unit using serial lines................................ 148
connecting ground to the transceiver................ 140
connecting ground to the Transceiver Unit......... 140
connecting the dual interface cable from the
Operating Panel to the Processor Unit............. 146
connecting the grounding cable to the Operating
Panel ................................................... 147
connecting the Operating Panel Power Supply
to the Processor Unit................................. 142
connecting the Processor Unit to the
transceiver ............................................. 150
connecting the Processor Unit to the Transceiver
Unit..................................................... 150
connecting the transducer plug to the
Transceiver Unit ...................................... 188
connecting the uninterruptible power supply to
AC mains and vessel ground........................ 138
connecting the USB interface cable from the
Operating Panel to the Processor Unit............. 145
connecting the video cable ........................... 143
connecting vessel ground and AC mains to
display ................................................. 141
connecting vessel ground to computer .............. 139
connecting vessel ground to Enix computer ........ 139
connecting vessel ground to Processor Unit ........ 139
defining the file and folder preferences for data
recording............................................... 202
defining the location of the GPS ..................... 198
defining the location of the motion reference
unit ..................................................... 197
defining the location of the transducer .............. 199
defining the sonar reference point ................... 195
designing, manufacturing and mounting the
installation blister ...................................... 91
designing, manufacturing and mounting the
installation hardware................................... 91
designing, manufacturing and mounting the
keel box.................................................. 91
designing, manufacturing and mounting the
sealing plate ............................................. 95
designing, manufacturing and mounting the
steel conduit............................................. 92
determining the location and installation angles
of the transducer ........................................ 88
installing the computer ................................ 118
installing the display .................................. 117
installing the Enix ..................................... 118
installing the mounting house .......................... 96
installing the Operating Panel........................ 120
installing the Operating Panel Power
Supply ................................................. 122
installing the Processor Unit ......................... 118
installing the transceiver .............................. 123
installing the Transceiver Unit ....................... 123
installing the transducer............................... 106
installing the transducer cables ................ 102, 104
installing the transducer into the mounting
house ................................................... 106
interfacing a motion sensor........................... 208
lifting the transducer up to its mounting
location ................................................ 100
lifting units and transportation boxes ............... 257
mounting the transducer .............................. 106
packing for storage or shipment ..................... 266
powering off ............................................ 215
powering up ............................................ 189
preparing a cable for termination .................... 174
preparing the transducer installation .................. 88
pulling the transducer cable through the steel
conduit ................................................. 104
pulling the transducer cables through the
sealing plate ........................................... 102
returning electronic modules to Kongsberg
Maritime ............................................... 272
returning printed circuit boards to Kongsberg
Maritime ............................................... 272
securing and terminating a cable..................... 175
selecting measurement units.......................... 194
setting to work ......................................... 179
setting up input from a navigation system.......... 204
setting up synchronization ............................ 209
transporting Kongsberg Maritime
equipment ............................................. 256
troubleshooting when the Transceiver Unit fails
to start.................................................. 191
unpacking a hydrophone .............................. 264
unpacking a mechanical unit ......................... 262
unpacking a sonar head ............................... 264
unpacking a transducer................................ 264
unpacking an electromechanical unit ............... 263
unpacking an electronic unit ......................... 263
unpacking and handling electronic modules ........ 270
unpacking and handling printed circuit
boards .................................................. 270
unpacking standard parts and units .................. 261
unpacking the transducer ............................... 98
using multi-diameter cable sealing ............ 108, 176
verifying basic operation.............................. 190
verifying that all cables are properly
connected .............................................. 182
verifying that operational power is correct ......... 181
visual inspection of units and transportation
boxes after arrival .................................... 258
procedures
cables .................................................... 136
creating mounting procedures............... 40, 81, 219
installation ................................................ 88
transducer installation ................................... 64
unpacking ............................................... 260
wiring.................................................... 136
Processor Unit
AC mains connection.................................. 139
best location .............................................. 45
cable plan ............................................... 132
compass safe distance ................................... 45
connecting external devices using Ethernet ........ 149
connecting external devices using serial
lines .................................................... 148
connecting to the transceiver ......................... 150
connecting to the Transceiver Unit .................. 150
connection to display .................................. 143
description ................................................ 20
environmental requirements.......................... 253
graphic adapter ......................................... 152
installation .............................................. 118
outline dimensions..................................... 250
outline dimensions drawing .......................... 223
overview .................................................. 20
power requirements.................................... 252
Simrad SN90