Keysight Technologies B1505A Configuration Manual Download Page 42

Page: 42 / 298

1-34

Keysight B1505A Configuration and Connection Guide

Configuration Guide
N1268A Ultra High Voltage Expander

NOTE

The HPSMU and MPSMU modules cannot be used with the Ultra High Voltage Unit
(UHVU) even when protection adapters are used.

Model/Option

Description

Additional Information

16493V-001

10 kV Ultra High Voltage Cable, 1.5 m

•

One UHV cable (Red) and one SHV cable
(Black) are included in the
16493V-001/002.

•

These cables are used to connect between
the N1268A UHV Expander and the
N1265A Ultra High Current
Expander/Fixture or a prober.

•

Cable length 1.5 m or 3.0 m can be
specified by option 001 or 002.

16493V-002

10 kV Ultra High Voltage Cable, 3 m

N1254A-520

10 kV Ultra High Voltage Open End Cable, 1
m.

•

One-side 10kV UHV/SHV and the
other-side open end

•

These cables are used to connect between
the N1268A UHV output and a device
under test (DUT) placed inside the
N1265A.

Adapters

N1254A-103

Triaxial (m) to BNC (f) adapter

•

This adapter is needed when a B1512A
HCSMU is used as a voltage controller of
the N1268A. This adapter is used for
Force.

N1254A-517

Adapter, Triax Jack to Triaxial Plug

•

This adapter is needed when a B1512A
HCSMU is used as a voltage controller of
the N1268A. This adapter is used for
Sense.

Summary of Contents for B1505A











































































































































































































































































































Search results

Summary of Contents for B1505A

Reviews:

Related manuals for B1505A

Brands by name

Popular brands

Keysight Technologies B1505A, Configuration Manual

Search results

Summary of Contents for B1505A

Reviews:

Related manuals for B1505A

Brands by name

Popular brands