Keysight Technologies B1505A Configuration Manual Download Page 121 | Manualshive

Page: 121 / 298

background image

Keysight B1505A Configuration and Connection Guide

3-15

N1265A Connection Guide

Output Connection

Bias Tee Terminals

Output terminals internally connected to the Bias Tee High and Low input connectors on
the rear panel. The terminals should be connected to a DUT for performing the high
voltage C-V measurement.

High and Low must be connected to the high and low terminals of a DUT respectively.

Use SHV(plug)-SHV(plug) cable (N1254A-512), 2 ea. and SHV(jack)-banana adapter
(N1254A-513), 2 ea. for connection.

CAUTION

Open the Bias Tee terminals for the ultra high voltage measurement using UHVU.

K Thermocouple Terminals

For connecting the thermocouple to monitor temperature around a DUT.
The N1265A-041 thermocouple supports maximum of +180



C.

The N1254A-554 thermocouple supports maximum of +250



C.

«
...
119
120
121
122
123
...
»

Summary of Contents for B1505A











































































































































































































































































































Reviews:

No comments

Related manuals for B1505A

Brand: Lambrecht Pages: 5

Brand: Keithley Pages: 25

Brand: 3B6 Pages: 30

Brand: A&D Pages: 102

Brand: Kane Pages: 16

Brand: Bacharach Pages: 48

Brand: Bacharach Pages: 24

Brand: Macnaught Pages: 14

Brand: Kamstrup Pages: 100

Brand: Kamstrup Pages: 16

Brand: Kamstrup Pages: 12

Brand: Kamstrup Pages: 60

Brand: Kamstrup Pages: 136

Brand: Kamstrup Pages: 16

Brand: Kamstrup Pages: 155

Brand: Daewoo Pages: 17

Brand: Vectronics Pages: 4

HYDROMETTE HB 30

Brand: GANN Pages: 65

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands