Keysight Technologies B1505A Configuration Manual Download Page 16

Page: 16 / 298

1-8

Keysight B1505A Configuration and Connection Guide

Configuration Guide
B1505A Modules and Mainframe Options

Table 1-5

Mainframe Options

Description

Model/
Option

Note

Mainframe

Power Device Analyzer/Curve Tracer

B1505A

•

See

Table 1-3 on page 1-6

for furnished

accessories

Select modules (optional)

High Power Source/Monitor Unit module
(HPSMU), 200 V/1 A

B1510A-FG

•

Furnished with two triaxial cables
(16494A). Cable length 1.5 m or 3.0 m is
specified by 015 or 030.

•

Up to four modules can be installed.

•

The total number of installed HPSMU and
HCSMU modules cannot exceed 4.

Medium Power Source/Monitor Unit module
(MPSMU

）

, 100 V/100 mA

B1511B-FG

•

Furnished with two triaxial cables
(16494A). Cable length 1.5 m or 3.0 m is
specified by 015 or 030.

•

Up to ten modules can be installed.

High Current Source/Monitor Unit module
(HCSMU), 20 A at 20 V

B1512A-FG

•

Furnished with one pair of high current
cables (16493S) and Kelvin adapter
(16493S-010). Cable length 1.5 m or 3.0 m
is specified by 015 or 030.

•

Up to two modules can be installed.

•

The total number of installed HPSMU and
HCSMU modules cannot exceed 4.

High Voltage Source/Monitor Unit module
(HVSMU), 3000 V at 4 mA

B1513C-FG

•

Furnished with one HVSMU cable
(16493T). Cable length 1.5 m or 3.0 m is
specified by option 015 or 030.

•

Up to five modules can be installed.

Medium Current Source Monitor Unit
module (MCSMU), 1 A at 30 V

B1514A-FG

•

Furnished with two triaxial cables
(16494A). Cable length 1.5 m or 3.0 m is
specified by 015 or 030.

•

Up to six modules can be installed.

Multi Frequency Capacitance Measurement
Unit module (MFCMU)

B1520A-FG

•

Furnished with one CMU cable (N1300A).
Cable length 1.5 m or 3.0 m is specified by
option 015 or 030.

•

Up to one modules can be installed.

Specify the cable length (mandatory)

1.5m cable

015

•

Same cable length is applied to all
furnished cables.

3.0m cable

030

Summary of Contents for B1505A











































































































































































































































































































Search results

Summary of Contents for B1505A

Reviews:

Related manuals for B1505A

Brands by name

Popular brands

Keysight Technologies B1505A, Configuration Manual

Search results

Summary of Contents for B1505A

Reviews:

Related manuals for B1505A

Brands by name

Popular brands