Keysight Technologies B1505A Configuration Manual Download Page 67

Page: 67 / 298

Keysight B1505A Configuration and Connection Guide

1-59

Configuration Guide

Other Accessories

N1254A-516

BNC(f)-BNC(f)-BNC(f) adapter, 1 ea.

N1254A-517

Triax(f)-Triax(m) adapter, shield separated, 1 ea.

N1254A-518

SHV(plug)-SHV(plug) coaxial cable, 1.5 m, 1 ea.

N1254A-520

UHV(plug) to no connector cable, 1 m, 1 ea. and
SHV(plug) to no connector cable, 1 m, 1 ea.

N1254A-521

UHV(jack)-UHV(jack) adapter, 1 ea. and
SHV(jack)-SHV(jack) adapter, 1 ea.

N1254A-522

Connection wire, banana-to-banana, maximum 1500
A, 2 ea.

N1254A-523

Banana to no connector wire, maximum 1500 A, 1
m, 2 ea.

N1254A-524

System cable for prober, 1.8 m, 1 ea.

N1254A-525

SHV Cable Assy 1.5m - SHV Plug To Open-end, 1
ea.

N1254A-526

Ultra High Current Cable, 2m, No Connectors At
Either End, 1 ea.

N1254A-527

PTFE Standoff, Jack, 4 ea.

N1254A-528

PTFE Standoff With Banana Plug, 4 ea.

N1254A-554

Thermocouple, Type K, 75 cm, 2 ea.

N1254A-556

Test Leads and Connection Kit for Capacitance Test,
four 20 cm alligator clip - lug cables, four banana
plugs, four nuts, and four spare clips

Model/Option

Description Additional

Information

Summary of Contents for B1505A











































































































































































































































































































Search results

Summary of Contents for B1505A

Reviews:

Brands by name

Popular brands

Keysight Technologies B1505A, Configuration Manual

Search results

Summary of Contents for B1505A

Reviews:

Brands by name

Popular brands