Keysight Technologies B1505A Configuration Manual Download Page 288

Page: 288 / 298

7-70

Keysight B1505A Configuration and Connection Guide

Connection and Ordering Examples
GaN Current Collapse / Dynamic On-Resistance Measurement System using the N1267A

Non-Kelvin Connection with Prober for On-Wafer Lateral
Device

•

Device Type: Lateral MOSFET (3 terminals)

•

Key Specification

•

Max Voltage/Current: 3 kV/20 A

Figure 7-37

Connection example

NOTE

Prober vendor is responsible for cabling inside the shielding box.

Table 7-34

Ordering example

Model/Option

Quantity

Description

B1505A

Power Device Analyzer/Curve Tracer mainframe

B1512A-FG

High Current Source Monitor Unit, 20 A/20 V(Pulsed); 1 A/40 V(DC)

B1513C-FG

High Voltage Source Monitor Unit, 3000 V/4 mA (Pulsed & DC)

B1514A-FG

Medium Current Source Monitor Unit, 1 A/30 V(Pulsed), 100 mA/30 V(DC)

N1267A

High Voltage Source Monitor Unit / High Current Source Monitor Unit Fast
Switch

16493S

High Current Source Monitor Unit Cable

16493S-011

High Current Source Monitor Unit non-Kelvin Adapter

8120-1838

BNC Cable, 30 cm

1250-2405

BNC-T Plug (m)-BNC (f)-BNC (f) adapter, 1ea

N1254A

Accessories for instruments and fixtures

HVSMU

HCSMU

GNDU

MCSMU

B1505A

N1267A

For Gate

Chuck

N1267A

For Drain

HCSMU Non-

Kelvin adapter

16493S-011

High

Low

HCSMU Non-

Kelvin adapter

16493S-011

N1254A-104 TRX(J) to BNC(P) adapter

8120-1838
BNC Cable, 30 cm

MCSMU

For Chuck

N1254A-104 TRX(J) to BNC(P) adapter

16494A (Included in the MCSMU)

16493T (Included in the HVSMU)

16493S (Included in the HCSMU)

16494A (Included in the MCSMU)

16493L (Included in B1505A)

1250-2405
Plug-BNC (f)-BNC (f)

N1262A-036 50 Ohm
T ermina

on Adapter

HVSMU

F
S

HCSMU

MCSMU

GNDU

Summary of Contents for B1505A











































































































































































































































































































Search results

Summary of Contents for B1505A

Reviews:

Brands by name

Popular brands

Keysight Technologies B1505A, Configuration Manual

Search results

Summary of Contents for B1505A

Reviews:

Brands by name

Popular brands