manualshive.com logo in svg

Keysight Technologies B1505A, Configuration Manual

Share
Download
Keysight Technologies B1505A Configuration Manual Download Page 147

Keysight B1505A Configuration and Connection Guide

4-15

N1272A and N1273A Connection Guide

Output Connection

Accessories for Connecting a DUT

Use the test lead kit furnished with the N1273A to connect a device that cannot be 
connected to any socket module.

See the following simple instruction.

•

Requirements:

•

Test Leads and Connection Kit for Capacitance Test (N1254A-556), 
four 20 cm alligator clip - lug cables, four banana plugs, four nuts, and four spare 
clips

•

DUT

•

Instruction: 

1. Put your DUT on the blank silicon plate.

2. Connect your DUT to the measurement terminals of the test fixture by using the test 

leads.

3. Close the fixture cover and perform measurement.

WARNING

Hazardous voltage, instrument maximum output voltage may appear at the 
measurement terminals if the fixture cover is closed.

WARNING

Open the AC/DC Guard terminal to avoid electrical shock, instrument damage, or 
DUT damage. Do not connect anything to this terminal which may have the same 
potential as the Collector/Drain terminal.

WARNING

Make sure that the cover is closed properly before starting measurement. Do not 
perform the measurement when a wire is protruding from the fixture cover.

Summary of Contents for B1505A











































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands