Keysight Technologies B1505A Configuration Manual Download Page 196

Page: 196 / 298

5-48

Keysight B1505A Configuration and Connection Guide

Connection Guide for Wafer Prober and Your Own Test Fixture
To Install an Interlock Circuit

Procedure

Prepare the required parts listed in

Table 5-38

. And install the interlock circuit as shown

below.

1. Make mounting hole for the interlock connector. See

Figure 5-26

for dimensions.

2. Mount two mechanical switches on your shielding box, so that the switches close when

the door of the shielding box is closed, and open when the door is opened. For the
dimensions of the switch, see

Figure 5-27

below.

3. Mount an LED on your shielding box. For the dimensions of the LED, see

Figure 5-25

4. Use wire to connect the two switches in series between pin number 1 and 2 (or 3) of the

interlock connector. See

Figure 5-24

5. Use wire to connect the LED between pin number 4 and 5 (or 6) of the interlock

connector. See

Figure 5-24

6. Attach the interlock connector to the mounting hole.

If Keysight B1505A Interlock connector is connected to the interlock circuit, Keysight
B1505A SMU

cannot

force more than ± 42 V when the door is open. When the door is

closed, it can force more than ± 42 V.

When more than ± 42 V is forced from an SMU, the LED lights to indicate

high voltage

output

Figure 5-25

Dimensions of the LED (Keysight part number 1450-0641)

Figure 5-26

Dimensions of Mounting Hole for the Interlock Connector

5.6

Units : mm

Anode (+)

Cathode (

)

1.8

8.2

5.1

Summary of Contents for B1505A











































































































































































































































































































Search results

Summary of Contents for B1505A

Reviews:

Related manuals for B1505A

Brands by name

Popular brands

Keysight Technologies B1505A, Configuration Manual

Search results

Summary of Contents for B1505A

Reviews:

Related manuals for B1505A

Brands by name

Popular brands