Keysight Technologies B1505A Configuration Manual Download Page 160

Page: 160 / 298

5-12

Keysight B1505A Configuration and Connection Guide

Connection Guide for Wafer Prober and Your Own Test Fixture
Connection Overview

N1274A

On-wafer gate charge measurement
adapter/selector for 20 A/3 kV

For on-wafer gate charge measurements
using the HCSMU (max. 20 A) and
HVSMU (max. 3 kV).

N1275A

On-Wafer gate charge measurement adapter for
N1265A

For on-wafer gate charge measurements
with the UHCU (max. 500 A) and
HVSMU (max. 3 kV).

N1254A-103

BNC(f)-Triaxial(m) adapter, triaxial shield open

For using HCSMU instead of MCSMU

N1254A-517

Triax(f)-Triax(m) adapter, shield separated

N1254A-104

BNC(m)-Triaxial(f) adapter, triaxial shield open

For using MCSMU instead of HCSMU

N1254A-106

BNC(f)-Triaxial(m) adapter, triaxial guard open

For changing N1262A-010 triax to BNC

N1254A-402

Interlock micro switch

For making interlock circuit. See

"To

Install an Interlock Circuit" on page
5-47

1252-1419

Interlock connector (6 pin, female)

1450-0641

LED (V



2.1 V @ I

= 10 mA)

N1254A-500

HV(jack) connector, panel mount, for soldering

For connecting HVSMU or accessory to
your DUT interface.

N1254A-501

HV(jack)-HV(jack) adapter, panel mount

N1254A-502

HV(plug) connector, panel mount, for soldering

N1254A-503

BNC(m) to no connector coaxial cable, 1.5 m

For connecting accessory to your DUT
interface.

N1254A-504

HV(jack) to no connector coaxial cable, 1.5 m

N1254A-505

HV(plug) to no connector triaxial cable, 1.5 m

N1254A-506

HV(plug) to no connector coaxial cable, 1.5 m

N1254A-507

HV(plug)-HV(plug) coaxial cable, 1.5 m

N1254A-516

BNC(f)-(f)-(f) adapter

N1254A-518

SHV(plug)-SHV(plug) coaxial cable, 1.5 m

For connecting N1260A to N1265A.

N1254A-520

UHV(plug) to no connector cable, 1 m and
SHV(plug) to no connector cable, 1 m

For connecting UHVU to your DUT
interface.

N1254A-521

UHV(jack)-UHV(jack) adapter and
SHV(jack)-SHV(jack) adapter

N1254A-523

Banana to no connector wire, 1 m, 2 ea.

For connecting UHCU to probe station.

N1254A-524

System cable for prober, 1.8 m

Model/Option

Description

Remarks

Summary of Contents for B1505A











































































































































































































































































































Search results

Summary of Contents for B1505A

Reviews:

Related manuals for B1505A

Brands by name

Popular brands

Keysight Technologies B1505A, Configuration Manual

Search results

Summary of Contents for B1505A

Reviews:

Related manuals for B1505A

Brands by name

Popular brands