manualshive.com logo in svg

Keysight Technologies B1505A, Configuration Manual

The Keysight Technologies B1505A Handbook is a comprehensive manual offering detailed insights into operating the B1505A device. This user manual is available for free download on our website, allowing users to access valuable information and maximize their experience with the B1505A. Grab your free copy at manualshive.com.

Share
Download
background image

3-2

Keysight B1505A Configuration and Connection Guide

N1265A Connection Guide

This chapter describes the required information for connecting Keysight B1505A, 
N1265A, and a device under test (DUT).

•

"Input Connection"

•

"Output Connection"

The N1265A is a test fixture which contains the current expander to enable 500 A or 1500 
A (option N1265A-015) output and measurement, and contains the selector to switch the 
measurement resource connected to the DUT.

The current expander is used to configure ultra high current unit (UHCU).

The selector is used to switch the measurement resource connected to the DUT. The 
measurement resource will be the UHCU, HVSMU/HVMCU, or HP/MPSMU. The 
selector output can be extended to your prober station by using the N1254A-524 ultra high 
current prober system cable.

The N1265A also provides the connection paths for UHVU, MFCMU via bias-tee, and 
HP/MP/HC/MC/DHCSMU.

•

Dimensions: 420 mm (W) 

 285 mm (H) 

 575 mm (D)

•

Weight: 30.0 kg

•

Maximum volt-amps: 400 VA

WARNING

To avoid electrical shock and instrument damage, turn the all instruments off before 
connecting or disconnecting measurement cable.

WARNING

There are potentially hazardous voltages of up to ± 10 kV (UHVU), ± 3000 V 
(HVSMU), ± 2200 V (HVMCU), ± 200 V (HPSMU), or ± 100 V (MPSMU) at the High, 
Force, Guard, and Sense terminals. To prevent electrical shock, do not expose these 
lines.

WARNING

To prevent electrical shock during use, connect the Interlock cable (see 

"To Connect 

Interlock Circuit" on page 3-5

).

WARNING

The B1505A, the N1265A ultra high current expander/fixture, and the N1268A ultra 
high voltage expander are heavy and require a two person lift.

CAUTION

Do not grab the fixture cover when lifting the N1265A.

CAUTION

Never connect the Guard terminal to any output, including circuit common, chassis 
ground, or any other guard terminal. Connecting anything may damage the instrument.

CAUTION

Never connect the UHVU High, HVMCU High, and HVSMU Force and Guard terminals 
to any output, including circuit common, chassis ground, or any other measurement 
resource such as SMU. Connecting other measurement resource may damage the 
connected one.

CAUTION

Never connect the UHVU Low terminal to any other measurement resource except for the 
N1269A or N1265A-040 adapter. Connecting other measurement resource may damage 
the connected one.

Summary of Contents for B1505A











































































































































































































































































































Reviews:

No comments

Related manuals for B1505A

Yamaha 142 Reference preview
142
Brand: Yamaha Pages: 8
UEi C257 Instruction Manual preview
C257
Brand: UEi Pages: 20
Hach A1000 Basic User Manual preview
A1000
Brand: Hach Pages: 138
IEI Technology IW04-MB14-N User Manual preview
IW04-MB14-N
Brand: IEI Technology Pages: 85
NanoEnTek JuLi Stage Installation Manual preview
JuLi Stage
Brand: NanoEnTek Pages: 4
NARDA nbm-520 Operating Manual preview
nbm-520
Brand: NARDA Pages: 64
Vanguard Instruments Company WRM-10P User Manual preview
WRM-10P
Brand: Vanguard Instruments Company Pages: 62
Vanguard Instruments Company IRM-5000P User Manual preview
IRM-5000P
Brand: Vanguard Instruments Company Pages: 58
Pangea TM50 Setup Procedure preview
TM50
Brand: Pangea Pages: 2
Gas Data GFM 436 User Manual preview
GFM 436
Brand: Gas Data Pages: 99
E+E Elektronik EE772 User Manual preview
EE772
Brand: E+E Elektronik Pages: 32
FM Marin Gobius 4 Waste Installation Manual preview
Gobius 4 Waste
Brand: FM Marin Pages: 8
ThermoFisher Scientific Thermo Scientific iCE 3000 Series Pre-Installation Manual preview
Thermo Scientific iCE 3000 Series
Brand: ThermoFisher Scientific Pages: 42
F&F WNC-3 Manual preview
WNC-3
Brand: F&F Pages: 4
RedBack Lasers DA530L Instruction Manual preview
DA530L
Brand: RedBack Lasers Pages: 2
Oceanic PROPLUS X Service Procedure preview
PROPLUS X
Brand: Oceanic Pages: 9
Valor TPMS GAUGE User Manual preview
TPMS GAUGE
Brand: Valor Pages: 42
KLINGER Minimag Operation Manual preview
Minimag
Brand: KLINGER Pages: 20

Brands by name

Popular brands

Load more brands