Keysight Technologies B1505A Configuration Manual Download Page 185 | Manualshive

Page: 185 / 298

background image

Keysight B1505A Configuration and Connection Guide

5-37

Connection Guide for Wafer Prober and Your Own Test Fixture

To Connect Ultra High Current Expander

Table 5-29

Cables for connecting Prober Side of N1254A-524 System Cable

CAUTION

Never connect the High Force and High Sense terminals to any output, including circuit
common, chassis ground, or any other measurement resource such as SMU. Connecting
other measurement resource may damage the connected one.

Connecting System Cable to N1265A

Requirements

•

Box wrench, M5 hex

•

Clear plastic plate, 2 ea. (furnished with the N1254A-524 system cable)

Procedure

1. Turn the all instruments off.

2. Remove power cable from the all instruments.

3. Open the fixture cover of the N1265A.

4. Remove connection wire from the Selector Output and Gate terminals if the wire is

connected.

5. Remove the clear plastic plate from the fixture cover. This makes opening for passing

the cable through. Use the box wrench and unscrew six hex nuts to remove the plate.

Treasure the removed plate. It must be replaced in the normal use conditions without
the N1254A-524 system cable.

6. Connect two connector boxes of the system cable to the Selector Output and Gate

terminals properly. See

7. Pull out the prober side connector box and some long of extension cable

(approximately 1.5 m) from the opening.

8. Set and fix two clear plastic plates to the fixture cover by using the hex nuts removed in

the step 5. The plates close the excess opening and make the opening enough to pass
the cable through.

9. Close the fixture cover.

10. Connect the 16493J interlock cable from the B1505A or the N1268A to the interlock

circuit installed in the probe station.

WARNING

For using the prober system cable safely

Never connect the interlock cable to the N1265A.

Never remove the clear plastic plates from the fixture cover.

N1254A-524

connectors

Required cables/Description

Connect to

Low Force

Ultra high current cable with banana(plug). N1254A-523 can be used.

DUT low terminal

(ex: source)

Low Sense

Coaxial cable with BNC(m) connector. N1254A-503 can be used.

High Force

Ultra high current cable with banana(plug). N1254A-523 can be used.

DUT high terminal

(ex: drain)

High Sense

Triaxial cable with HV(plug) connector. N1254A-505 can be used.

Gate

Coaxial cable with BNC(m) connector. N1254A-503 can be used.

DUT drive terminal

(ex: gate)

«
...
183
184
185
186
187
...
»

Summary of Contents for B1505A











































































































































































































































































































Reviews:

No comments

Related manuals for B1505A

Brand: Farfisa Pages: 14

Brand: Valmet Pages: 63

Brand: LaMotte Pages: 2

Brand: Kane Pages: 19

Brand: RayTek Pages: 72

Brand: Magnetrol Pages: 40

Brand: ICM Controls Pages: 8

Brand: Unipulse Pages: 129

Brand: IDEAL Pages: 11

Brand: IDEAL Pages: 16

Brand: IFR Pages: 46

Bass Master Rockabilly

Brand: K&K Sound Pages: 2

Brand: JGR Pages: 12

Brand: VEE GEE Pages: 2

Brand: Vega Pages: 28

Brand: Vega Pages: 20

Brand: Xantrex Pages: 2

Brand: Xaoc Devices Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands