manualshive.com logo in svg

Keysight Technologies B1505A, Configuration Manual

Share
Download
Keysight Technologies B1505A Configuration Manual Download Page 24

1-16

Keysight B1505A Configuration and Connection Guide

Configuration Guide
N1259A Test Fixture for Power Device

NOTE

The N1259A-020 high voltage bias-T and/or the N1259A-300 module selector can be 
installed in the N1259A-001 test fixture later. For upgrade kit, please refer to 

"Upgrade Kit 

for N1259AU Test Fixture" on page 1-65

. Keysight Technologies service center is 

responsible for N1259AU-020 and N1259AU-300 installation.

Model/Option

Description

Additional Information

16493S-021 

Dual HCSMU combination adapter, for 40 A 
measurement

•

Output connectors are compatible with 
B1512A HCSMU.

•

The 16493S-021 is furnished with one 
30cm Triaxial cable and one 30 cm High 
current coaxial cable for output 
connection.

•

Do not connect or put any conductor on 
the HCSMU Low Force and Low Sense 
terminals, outer conductor of the coaxial 
connectors. Connecting or locating 
conductor of circuit common, chassis 
ground, or any potential on causes the 
measurement error.

N1254A-104

Triax (f) to BNC (m) adapter

•

This adapter is required when a B1514A 
MCSMU is connected to the HCSMU 
ports of the N1259A Fixture. This adapter 
is used for Force terminal.

Summary of Contents for B1505A











































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands