manualshive.com logo in svg

Keysight Technologies B1505A, Configuration Manual

Share
Download
Keysight Technologies B1505A Configuration Manual Download Page 47

Keysight B1505A Configuration and Connection Guide

1-39

Configuration Guide

N1271A Thermal Test Enclosure and Related Accessories

Measurement Capability on Thermal Test

The B1505A measurement capabilities supported on the thermal test are summarized in 

Table 1-16

. Qg tests are not supported on the thermal test.

Table 1-16

Measurement Capability and Requirements

Information of inTEST Thermal Plate and Thermostream

The B1505A with the N1271A supports the Thermal Plate and the Thermostream of 
inTEST corporation. Supported models are listed below but contact inTEST for more 
information, 

[email protected]

.

Capability

Fixture

Thermal Plate 

Solution

Thermostream 

Solution

•

IV test up to 20 A, 3 kV

N1259A

Yes 

(with N1271A-001)

No

•

IV test up to 1500 A, 3 kV

N1265A

Yes 

(with N1271A-001)

Yes

(with N1271A-002)

•

IV test up to 1500 A, 10 kV

•

CV  test

N1265A

Yes 

(with N1271A-001)

Yes

(with N1271A-005)

•

Qg test up to 20 A, 3 kV

N1259A

No

No

•

Qg test up to 1100 A, 3 kV

N1265A

No

No

Summary of Contents for B1505A











































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands