background image

Ratek TH8000/TH8200 Precision Immersion Heater Circulator - User Manual 

------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- 

------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- 

Page 1 of 25

 

 

User Manual

 

Precision Immersion Heater Circulator 

Models : TH8000, TH8200 

 

Version: 1.1 – 16/06/2015 

English 

 
 

 

 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

 

www.ratek.com.au

www.ratek.com.au

www.ratek.com.au

www.ratek.com.au

 

 

60 Wadhurst Dve, Boronia, Victoria 3155, Australia - P: +613 9887 2161 - F: +613 9887 2163 - E: 

[email protected]

 

© All Rights Reserved 

 

Made in Australia, User Manual printed in Australia 

Changes without prior notification reserved 

Errors and omissions excepted.

 

U

se

r M

an

ua

 

 

 

 

 

 

 

 

  T

H

8

x0

0

 –

 P

re

cis

io

Im

m

er

sio

H

ea

te

r C

ir

cu

la

to

Summary of Contents for TH8000


























Reviews: