302
i-
α
ppli
e
When you reply with a quote or forward an i-mode
mail, an i-
α
ppli launch specification can not be
quoted. You cannot also quote a launch specification
when forwarding a mail using DoCoMo keitai datalink,
etc. or Infrared data exchange function.
e
i-
α
ppli programs cannot be launched from i-mode
mails in Secret folders.
Launching an i-
α
ppli using the
Infrared data exchange function
This setting allows you to launch an i-
α
ppli when
receiving the i-
α
ppli launch signal during Infrared
data exchange.
a
i
X
"LIFE KIT"
X
"Receive Ir data"
X
"Receive"
X
Receive the i-
α
ppli
launch signal
Launching an i-
α
ppli using
the Bar code reader
This setting allows you to launch an i-
α
ppli
using the Bar code reader when a scanned bar
code includes an i-
α
ppli launch specification.
a
i
X
"LIFE KIT"
X
"Bar code
reader"
X
Scan a bar code
b
Select an item to launch a program
X
"YES"
Launching an i-
α
ppli using
the IC card function
This setting allows you to launch an i-
α
ppli using
the IC card function by holding the FeliCa mark
on a FOMA terminal over a reader/writer unit.
c
A program does not start up in the following
situations:
a
When another function is running
a
During a call
a
When the program to launch is not installed or
partly downloaded
c
When IC card lock is set, you cannot launch an
i-
α
ppli with the IC card function. When you
launch an i-
α
ppli with other function than IC card
while IC card lock is set, you cannot use the IC
card function with the i-
α
ppli.
a
Hold the FeliCa mark "
" on a
FOMA terminal over a reader/writer unit
Launching an i-
α
ppli from ToruCa
When an i-
α
ppli launch specification is pasted
into an acquired ToruCa, you can launch the
i-
α
ppli program from the ToruCa.
a
ToruCa display screen (p.309)
X
Select an item to launch a program
X
"YES"
<Set i-
α
ppli stand-by>
Setting the i-
α
ppli Standby Screen
Use this function to set a selected i-
α
ppli
program as the standby screen on your FOMA
terminal. When the i-
α
ppli standby screen
appears, "
" or "
" appears at the bottom of
the screen.
c
Only one i-
α
ppli program can be set as the
i-
α
ppli standby screen.
c
Some programs cannot be set as the standby screen.
a
Software list screen (p.295)
X
p
(FUNC)
X
"Software setting"
X
"Stand-by
display"
X
"ON"
X
o
(Finish)
e
"
" appears for the program set as the standby screen.
e
If a program that communicates is set as the i-
α
ppli
standby screen, it may not run correctly due to poor
signal status, etc.
e
If you select "OFF" for "Stand-by net" in "Software setting",
you may not be able to receive timely information.
e
When the i-
α
ppli standby screen is set, the image set
for "Stand-by display" in "Display setting" (p.135)
does not appear.
e
Even if the i-
α
ppli standby screen is set, the screen
set in "Stand-by display" in "Display setting" appears
when you switch tasks to show the standby screen.
e
If the power is cycled while the i-
α
ppli standby screen
is set, a message asking whether to launch the
i-
α
ppli standby screen appears.
e
If "Dial lock" (p.161) or "Original lock" (p.167) is set or
2in1 is set to B mode or Dual mode, while the i-
α
ppli
standby screen is displayed, the screen ends. If "Dial
lock" or "Original lock" is released or 2in1 is set to A
mode while the i-
α
ppli standby screen is displayed,
the screen reappears.
Running the i-
α
ppli standby screen
Runs the software set for the i-
α
ppli standby screen.
a
On the i-
α
ppli standby screen
X
t
The i-
α
ppli starts up and the "
" or "
" icon at
the bottom of the screen changes to the flashing
"
" or "
" icon.
NOTE
End
Start