manualshive.com logo in svg

Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion, Configuration Manual, Page: 435 / 742

Share
Download
Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion Configuration Manual Download Page 435

 

22-19

Catalyst 6500 Series Switch and Cisco 7600 Series Router Firewall Services Module Configuration Guide using ASDM

OL-20748-01

Chapter 22      Applying Application Layer Protocol Inspection

  DNS Inspection

How DNS Rewrite Works

When DNS inspection is enabled, DNS Rewrite provides full support for NAT of DNS messages 
originating from any interface.

If a client on an inside network requests DNS resolution of an inside address from a DNS server on an 
outside interface, the DNS A-record is translated correctly. If the DNS inspection engine is disabled, the 
A-record is not translated.

As long as DNS inspection remains enabled, you can configure DNS Rewrite using the 

alias

, 

static

, or 

nat 

commands. For details about the configuration required see the 

“Configuring DNS Rewrite” section 

on page 22-20

.

DNS Rewrite performs two functions:

•

Translating a public address (the routable or “mapped” address) in a DNS reply to a private address 
(the “real” address) when the DNS client is on a private interface.

•

Translating a private address to a public address when the DNS client is on the public interface.

In 

Figure 22-4

, the DNS server resides on the external (ISP) network. On the FWSM, a 

static

 command 

maps the real address of the web server (192.168.100.1) to the ISP-assigned address (209.165.201.5). 
When a web client on the inside interface attempts to access the web server with the URL 
http://server.example.com, the host running the web client sends a DNS request to the DNS server to 
resolve the IP address of the web server. The FWSM translates the non-routable source address in the IP 
header and forwards the request to the ISP network on its outside interface. When the DNS reply is 
returned, the FWSM applies address translation not only to the destination address, but also to the 
embedded IP address of the web server, which is contained in the A-record in the DNS reply. As a result, 
the web client on the inside network gets the correct address for connecting to the web server on the 
inside network. For the exact NAT and DNS configuration for this example, see 

Example 22-2

. For 

configuration instructions for scenarios similar to this one, see the 

“Configuring DNS Rewrite with Two 

NAT Zones” section on page 22-21

.

Figure 22-4

DNS Rewrite with Two NAT Zones

DNS Rewrite also works if the client making the DNS request is on a DMZ network and the DNS server 
is on an inside interface. For an illustration and configuration instructions for this scenario, see the 

“DNS 

Rewrite with Three NAT Zones” section on page 22-22

.

132972

Web server

server.example.com

192.168.100.1

Web client

http://server.example.com

192.168.100.2

ISP Internet

DNS server

server.example.com IN A 209.165.200.225

 FWSM

192.168.100.1IN A 209.165.200.225

Summary of Contents for 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion







































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments