manualshive.com logo in svg

Chevrolet silverado 2012, Owner'S Manual

The Chevrolet Silverado 2012 Owner's Manual is a comprehensive guide designed to assist owners in understanding their truck's features and maintenance procedures. This essential manual provides detailed instructions and information, and it is available for free download at manualshive.com. Get yours today and empower yourself with the knowledge to maximize your Silverado's performance.

Share
Download
background image

Black plate (11,1)

Chevrolet Silverado Owner Manual - 2012

Vehicle Care

10-11

How to Reset the Engine Oil
Life System

Reset the system whenever the
engine oil is changed so that the
system can calculate the next
engine oil change. Always reset the
engine oil life to 100% after every oil
change. It will not reset itself. To
reset the system on most vehicles:

1. Display the OIL LIFE

REMAINING on the DIC. If the
vehicle does not have DIC
buttons, the vehicle must be in
P (Park) to access this display.
See

Driver Information Center

(DIC) on page 5

‑

33

.

2. Press and hold the SET/RESET

button on the DIC, or the trip
odometer reset stem if the
vehicle does not have DIC
buttons, for more than
five seconds. The oil life will
change to 100%.

On all vehicles, the Engine Oil Life
System can be reset as follows:

1. Turn the ignition to ON/RUN with

the engine off.

2. Fully press the accelerator pedal

slowly three times within
five seconds.

3. Display the OIL LIFE

REMAINING on the DIC. If the
display shows 100%, the system
is reset. See

Driver Information

Center (DIC) on page 5

‑

33

.

If the vehicle has a CHANGE
ENGINE OIL SOON message and it
comes back on when the vehicle is
started and/or the OIL LIFE
REMAINING is near 0%, the engine
oil life system has not been reset.
Repeat the procedure.

Automatic Transmission
Fluid (4-Speed
Transmission)

When to Check and Change
Automatic Transmission Fluid

A good time to check the automatic
transmission fluid level is when the
engine oil is changed.

Change the fluid and filter at the
intervals listed in

Maintenance

Schedule on page 11

‑

3

and be sure

to use the transmission fluid listed in

Recommended Fluids and
Lubricants on page 11

‑

13

.

Summary of Contents for silverado 2012

































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for silverado 2012

Daihatsu Mira Manual preview
Mira
Brand: Daihatsu Pages: 340
Camcar 40000 Manual preview
40000
Brand: Camcar Pages: 6
hager witty park XEV6 Series Installation Manual preview
witty park XEV6 Series
Brand: hager Pages: 9
B-Speech Pago INBTHF020 User Manual preview
Pago INBTHF020
Brand: B-Speech Pages: 24
Chrysler Stratus LHD 1997 Interactive Electronic Service Manual preview
Stratus LHD 1997
Brand: Chrysler Pages: 1534
Alpitronic Hypercharger HYC 075 Operation Instructions And Installation Manual preview
Hypercharger HYC 075
Brand: Alpitronic Pages: 64
SCC Quik Grip Installation And Removal Instructions preview
Quik Grip
Brand: SCC Pages: 4
AMP Research BEDXTENDER HD MAX 74841-00A Assembly Installation Manual preview
BEDXTENDER HD MAX 74841-00A
Brand: AMP Research Pages: 9
Belkin F8V7058-APL User Manual preview
F8V7058-APL
Brand: Belkin Pages: 2
Curtis 1POLXP1000RP Installation & Owner'S Manual preview
1POLXP1000RP
Brand: Curtis Pages: 6
Black+Decker BXAE00011 Operating Instructions Manual preview
BXAE00011
Brand: Black+Decker Pages: 21
Beeper RW050RF User& Installer'S Manual preview
RW050RF
Brand: Beeper Pages: 20
N-Com Bluetooth Kit3 PLUS User Instructions And Safety preview
Bluetooth Kit3 PLUS
Brand: N-Com Pages: 36
FORM FIT 8F 00 Installation Instructions preview
8F 00
Brand: FORM FIT Pages: 2
RAM 1500 CLASSIC 2020 Owner'S Manual preview
1500 CLASSIC 2020
Brand: RAM Pages: 360
Ranger design 1525-PCX Installation Manual preview
1525-PCX
Brand: Ranger design Pages: 22
Edelbrock Turbocharger 15012 Installation Instructions preview
Turbocharger 15012
Brand: Edelbrock Pages: 1
GMC Yukon XL Denali 2015 Owner'S Manual preview
Yukon XL Denali 2015
Brand: GMC Pages: 439

Brands by name

Popular brands

Load more brands