Chevrolet silverado 2012 Owner'S Manual Download Page 39 | Manualshive

Page: 39 / 608

background image

Black plate (33,1)

Chevrolet Silverado Owner Manual - 2012

In Brief

1-33

Driver Information
Center (DIC)

The DIC display is located at the
bottom of the instrument panel
cluster. It shows the status of many
vehicle systems and enables
access to the personalization menu.

The DIC buttons are located on the
instrument panel, next to the
steering wheel.

Some vehicles do not have the
buttons shown, however some of
the menus can be viewed by using
the trip odometer reset stem.

3

:

Press to display the

odometer, trip odometer, fuel range,
average economy, fuel used, timer,
instantaneous economy and Active
Fuel Management

™

indicator, and

transmission temperature. The
compass and outside air
temperature will also be shown in
the display. The temperature will be
shown in °C or °F depending on the
units selected.

T

:

Press to display the oil life,

units, tire pressure readings for
vehicles with the Tire Pressure
Monitor System (TPMS), trailer
brake gain and output information
for vehicles with the Integrated
Trailer Brake Control (ITBC) system,
engine hours, compass zone
setting, and compass recalibration.

U

:

Press to customize the feature

settings on your vehicle. See

Vehicle Personalization (With DIC
Buttons) on page 5

‑

52

for more

information.

V

:

Press to set or reset certain

functions and to turn off or
acknowledge messages on the DIC.

For more information, see

Driver

Information Center (DIC) on
page 5

‑

33

.

Vehicle Customization

Some vehicle features can be
programmed by using the DIC
buttons next to the steering wheel.
These features include:

.

Language

.

Door Lock and Unlock Settings

.

RKE Lock and Unlock Feedback

.

Lighting

.

Chime Volume

.

Memory Features

See

Vehicle Personalization (With

DIC Buttons) on page 5

‑

52

.

«
...
37
38
39
40
41
...
»

Summary of Contents for silverado 2012

































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for silverado 2012

Brand: Wagan Pages: 12

Brand: Camcar Pages: 6

Brand: ABL Pages: 4

Brand: Whipple Pages: 3

Brand: RAM Pages: 76

Brand: Advantech Pages: 59

Brand: AA Products Pages: 6

Brand: Metra Electronics Pages: 5

Brand: Renkforce Pages: 4

1966 Spider 105

Brand: Alfa Romeo Pages: 46

Brand: Quadratec Pages: 14

OPTIA hybrid 2020

Brand: Kia Pages: 54

Brand: Buick Pages: 394

Brand: T-Tech Pages: 1

Brand: Hamron Pages: 6

Indash 75114-296

Brand: Panavise Pages: 2

Brand: Harbor Freight Tools Pages: 8

ProPlus 620066V01

Brand: PAT Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands