Chevrolet silverado 2012 Owner'S Manual Download Page 90 | Manualshive

Page: 90 / 608

background image

Black plate (18,1)

Chevrolet Silverado Owner Manual - 2012

3-18

Seats and Restraints

3. Push the latch plate into the

buckle until it clicks.

Pull up on the latch plate to
make sure it is secure. If the belt
is not long enough, see

Safety

Belt Extender on page 3

‑

23

.

If the latch plate will not go fully
into the buckle, check if the
correct buckle is being used.

Position the release button on
the buckle so that the safety belt
could be quickly unbuckled if
necessary.

4. If equipped with a shoulder belt

height adjuster, move it to the
height that is right for you. See

“

Shoulder Belt Height Adjuster

”

later in this section.

5. To make the lap part tight, pull

up on the shoulder belt.

It may be necessary to pull
stitching on the safety belt
through the latch plate to fully
tighten the lap belt on smaller
occupants.

To unlatch the belt, push the button
on the buckle. The belt should
return to its stowed position.

Before a door is closed, be sure the
safety belt is out of the way. If a
door is slammed against a safety
belt, damage can occur to both the
safety belt and the vehicle.

«
...
88
89
90
91
92
...
»

Summary of Contents for silverado 2012

































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for silverado 2012

Brand: AA Products Pages: 6

Brand: Lincoln Pages: 424

Brand: Volkswagen Pages: 26

iBoard IB-ZK406

Brand: APS Auto Parts Specialist Pages: 3

10-8002-C11998B

Brand: Saleen Pages: 12

2013 Buick Verano

Brand: Buick Pages: 5

STRONGARM RVR303

Brand: Blue Giant Pages: 48

Brand: FORM FIT Pages: 2

Brand: walser Pages: 24

Brand: Jeep Pages: 1528

Brand: Menabo Pages: 12

Polaris TATOU 4S

Brand: Camoplast Pages: 13

Brand: Ecco Pages: 12

Brand: Cadillac Pages: 352

Brand: FALCON RIDGE Pages: 4

OPTIA hybrid 2020

Brand: Kia Pages: 54

Brand: Z Flash Pages: 4

Brand: Mercedes-Benz Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands