Chevrolet silverado 2012 Owner'S Manual Download Page 524 | Manualshive

Page: 524 / 608

background image

Black plate (100,1)

Chevrolet Silverado Owner Manual - 2012

10-100

Vehicle Care

Notice:

If the jumper cables are

connected or removed in the
wrong order, electrical shorting
may occur and damage the
vehicle. The repairs would not be
covered by the vehicle warranty.
Always connect and remove the
jumper cables in the correct
order, making sure that the
cables do not touch each other or
other metal.

Jumper Cable Removal

A. Heavy, Unpainted Metal Engine

Part or Remote Negative (

−

)

Terminal

B. Good Battery or Remote

Positive (+) and Remote
Negative (

−

) Terminals

C. Dead Battery or Remote

Positive (+) Terminal

To disconnect the jumper cables
from both vehicles do the following:

1. Disconnect the black

negative (

−

) cable from the

vehicle that had the bad battery.

2. Disconnect the black

negative (

−

) cable from the

vehicle with the good battery.

3. Disconnect the red positive (+)

cable from the vehicle with the
good battery.

4. Disconnect the red positive (+)

cable from the other vehicle.

5. Return the positive (+) terminal

cover, to its original position.

«
...
522
523
524
525
526
...
»

Summary of Contents for silverado 2012

































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for silverado 2012

Brand: Daihatsu Pages: 1718

Brand: Yakima Pages: 11

Brand: RaceChip Pages: 20

Brand: Porsche Pages: 192

Brand: Gator Pages: 8

Brand: benbat Pages: 14

Brand: SPL Pages: 5

Alloy Rugged Ridge X-Clamp

Brand: Omix-Ada Pages: 2

Brand: Dodge Pages: 3

Brand: SilverLeaf Electronics Pages: 16

Brand: Carcomm Pages: 2

Brand: Mitsubishi Pages: 367

Brand: Car-Interface Pages: 23

Tipper Remote Kit

Brand: Nugent Pages: 21

Brand: Conrad Pages: 8

Brand: Ultraplast Pages: 5

Brand: Honda Pages: 279

Brand: Erich Jaeger Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands