Chevrolet silverado 2012 Owner'S Manual Download Page 193 | Manualshive

Page: 193 / 608

background image

Black plate (45,1)

Chevrolet Silverado Owner Manual - 2012

Instruments and Controls

5-45

PASSENGER DOOR OPEN

This message displays and a chime
may sound if the front passenger
door is not fully closed and the
vehicle is shifted out of P (Park).
Stop and turn off the vehicle, check
the door for obstructions, and close
the door again. Check to see if the
message still appears on the DIC.

RIGHT REAR DOOR OPEN
(Crew Cab)

This message displays and a chime
may sound if the passenger side
rear door is not fully closed and the
vehicle is shifted out of P (Park).
Stop and turn off the vehicle, check
the door for obstructions, and close
the door again. Check to see if the
message still appears on the DIC.

Engine Cooling System
Messages

ENGINE HOT A/C
(Air Conditioning)
TURNED OFF

This message displays when the
engine coolant becomes hotter than
the normal operating temperature.
See

Engine Coolant Temperature

Gauge on page 5

‑

17

. To avoid

added strain on a hot engine,
the air conditioning compressor
automatically turns off. When the
coolant temperature returns to
normal, the air conditioning
compressor turns back on. You can
continue to drive your vehicle.

If this message continues to appear,
have the system repaired by your
dealer as soon as possible to avoid
damage to the engine.

ENGINE OVERHEATED IDLE
ENGINE

Notice:

If you drive the vehicle

while the engine is overheating,
severe engine damage may
occur. If an overheat warning
appears on the instrument panel
cluster and/or DIC, stop the
vehicle as soon as possible. See

Engine Overheating on
page 10

‑

24

for more information.

This message displays when the
engine coolant temperature is too
hot. Stop and allow the vehicle to
idle until it cools down. See

Engine

Coolant Temperature Gauge on
page 5

‑

17

.

See

Overheated Engine Protection

Operating Mode on page 10

‑

27

for

information on driving to a safe
place in an emergency.

«
...
191
192
193
194
195
...
»

Summary of Contents for silverado 2012

































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for silverado 2012

Brand: Jeep Pages: 608

Brand: RAM Pages: 116

Brand: DAVIS Pages: 32

Brand: Whispbar Pages: 15

Brand: CALIMA Pages: 9

Brand: Ford Pages: 8

Brand: Intec Pages: 16

Tata Indigo Diesel

Brand: TATA Motors Pages: 190

Prime Design HBR-E-FT33B

Brand: Safe Fleet Pages: 12

Brand: RAM Pages: 496

Brand: cam Pages: 6

Quantum Wash'n'Wipe N30208

Brand: National Cycle Pages: 12

Brand: Ranger design Pages: 22

Brand: Toyota Pages: 285

transit connect 2012

Brand: Ford Pages: 299

Tri-Mount 34269

Brand: PowerMadd Pages: 2

Brand: Aries Pages: 4

Brand: Blue Sky Network Pages: 50

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands