Chevrolet silverado 2012 Owner'S Manual Download Page 416 | Manualshive

Page: 416 / 608

background image

Black plate (116,1)

Chevrolet Silverado Owner Manual - 2012

9-116

Driving and Operating

Trailer Gain Adjustment Procedure

Trailer Gain should be set for a
specific trailering condition and must
be adjusted any time vehicle
loading, trailer loading, or road
surface conditions change.

Setting the Trailer Gain properly is
needed for the best trailer stopping
performance. A trailer that is
over-gained may result in locked
trailer brakes. A trailer that is
under-gained may result in not
enough trailer braking. Both of these
conditions may result in poorer
stopping and stability of the vehicle
and trailer.

Use the following procedure to
correctly adjust Trailer Gain for each
towing condition:

1. Make sure the trailer brakes are

in proper working condition.

2. Connect a properly loaded trailer

to the vehicle and make all
necessary mechanical and
electrical connections. See

Vehicle Load Limits on
page 9

‑

17

for more information.

3. After the electrical connection is

made to a trailer equipped with
electric brakes:

.

A TRAILER CONNECTED
message will be briefly
displayed on the DIC.

.

The Trailer Brake Display
Page will appear on the
DIC showing TRAILER
GAIN and TRAILER
OUTPUT.

.

In the Trailer Output display
on the DIC,

“

- - - - - -

”

will

disappear if there is no
error present. Connecting a
trailer without electric
brakes will not clear the six
dashed lines.

4. Adjust the Trailer Gain by using

the gain adjustment (+ / -)
buttons on the Trailer Brake
Control Panel.

5. Drive the vehicle with the trailer

attached on a level road surface
representative of the towing
condition and free of traffic at
about 32 to 40 km/h (20 to
25 mph) and fully apply the
Manual Trailer Brake Apply
Lever.

Adjusting trailer gain at speeds
lower than 32 to 40 km/h (20 to
25 mph) may result in an
incorrect gain setting.

«
...
414
415
416
417
418
...
»

Summary of Contents for silverado 2012

































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for silverado 2012

Brand: Hama Pages: 2

Gemineye EC2014-C

Brand: Ecco Pages: 10

Reflex 5500 Series

Brand: Ecco Pages: 12

Brand: Ford Pages: 2

1973 Convertible

Brand: Volkswagen Pages: 80

Brand: Cadillac Pages: 522

Brand: AA Products Pages: 6

Brand: Meta System Pages: 16

Brand: Mercedes-Benz Pages: 91

Speed & Route Profiler

Brand: Racelogic Pages: 24

Brand: Ford Pages: 52

Grand Cherokee SRT 2019

Brand: Jeep Pages: 656

Brand: Navman Pages: 10

Brand: Macrom Pages: 10

Brand: Z Flash Pages: 4

Brand: Ranger design Pages: 22

Brand: PEUGEOT Pages: 232

DH-RB 05.02 Series

Brand: Dhollandia Pages: 65

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands