Chevrolet silverado 2012 Owner'S Manual Download Page 129 | Manualshive

Page: 129 / 608

background image

Black plate (57,1)

Chevrolet Silverado Owner Manual - 2012

Seats and Restraints

3-57

For regular cab models, there is an
anchor symbol on the covers to
assist you in locating the top tether
anchors.

Regular Cab

Do not install a child restraint in the
center seat position. See

Securing

Child Restraints (Center Front Seat
Position) on page 3

‑

65

or

Securing

Child Restraints (Right Front Seat
Position) on page 3

‑

65

or

Securing

Child Restraints (Rear Seat
Position) on page 3

‑

63

for more

information.

For regular cab models, the top
tether anchors are located under
covers on the back panel behind the
passenger seat. Remove the trim
plug to access the anchor. Be sure
to use an anchor located on the
same side of the vehicle as the
seating position where the child
restraint will be placed.

Crew Cab Shown, Extended Cab

Similar

For crew and extended cab models,
the top tether anchors are the loops
located near the top of the seatback
for each rear seating position.

«
...
127
128
129
130
131
...
»

Summary of Contents for silverado 2012

































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for silverado 2012

Brand: Jeep Pages: 212

Brand: Jeep Pages: 603

Brand: Jeep Pages: 80

QuadraTop Adventure Top S

Brand: Quadratec Pages: 20

Brand: Barker Pages: 2

2014 Grand Cherokee SRT8

Brand: Jeep Pages: 596

Brand: Skoda Pages: 4

Vehicle Asset Communicator

Brand: I.D. Systems Pages: 41

Prime Design OCM-3032

Brand: Safe Fleet Pages: 4

Brand: TracRac Pages: 8

Brand: Volvo Pages: 62

Brand: Nav TV Pages: 11

Brand: Toyota Pages: 204

Brand: Laser Pages: 3

Brand: Kargo Master Pages: 8

Brand: Kargo Master Pages: 14

Brand: Haltech Pages: 12

Brand: Ford Pages: 46

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands