Chevrolet silverado 2012 Owner'S Manual Download Page 484 | Manualshive

Page: 484 / 608

background image

Black plate (60,1)

Chevrolet Silverado Owner Manual - 2012

10-60

Vehicle Care

(B) TPC Spec (Tire
Performance Criteria
Specification)

:

Original

equipment tires designed to
GM's specific tire performance
criteria have a TPC specification
code molded onto the sidewall.
GM's TPC specifications meet or
exceed all federal safety
guidelines.

(C) Dual Tire Maximum Load

:

Maximum load that can be
carried and the maximum
pressure needed to support that
load when used in a dual
configuration. For information on
recommended tire pressure see

Tire Pressure on page 10

‑

65

and

Vehicle Load Limits on

page 9

‑

17

.

(D) DOT (Department of
Transportation)

:

The

Department of Transportation
(DOT) code indicates that the
tire is in compliance with the
U.S. Department of
Transportation Motor Vehicle
Safety Standards.

(E) Tire Identification Number
(TIN)

:

The letters and numbers

following the DOT code are the
Tire Identification Number (TIN).
The TIN shows the
manufacturer and plant code,
tire size, and date the tire was
manufactured. The TIN is
molded onto both sides of the
tire, although only one side may
have the date of manufacture.

(F) Tire Ply Material

:

The type

of cord and number of plies in
the sidewall and under the tread.

(G) Single Tire Maximum
Load

:

Maximum load that can

be carried and the maximum
pressure needed to support that
load when used as a single. For
information on recommended
tire pressure see

Tire Pressure

on page 10

‑

65

and

Vehicle Load

Limits on page 9

‑

17

.

«
...
482
483
484
485
486
...
»

Summary of Contents for silverado 2012

































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for silverado 2012

Brand: Jeep Pages: 25

Brand: Jeep Pages: 51

Brand: Farenheit Pages: 8

Brand: Xblitz Pages: 16

Brand: RAM Pages: 116

V2 SUPERCHARGER

Brand: Tesla Pages: 9

2011 Civic Sedan

Brand: Honda Pages: 5

990E0-54P56-000

Brand: Suzuki Pages: 12

Brand: BMW Pages: 55

Brand: Whispbar Pages: 15

Parrot MKi + ParrotCK3100 range LOGAN

Brand: Parrot Pages: 10

Brand: JKS Pages: 6

Brand: Jaeger Pages: 11

Brand: Power Acoustik Pages: 4

Brand: Skoda Pages: 324

Brand: AutoLoc Pages: 6

Brand: Curt Group Pages: 3

Brand: Juna Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands