Chevrolet silverado 2012 Owner'S Manual Download Page 295 | Manualshive

Page: 295 / 608

background image

Black plate (7,1)

Chevrolet Silverado Owner Manual - 2012

Climate Controls

8-7

Use the steps below to place the
entire system in automatic mode:

1. Press the AUTO button.

When AUTO is selected, the
display changes to show the
current temperature(s) and
AUTO is lit on the display. The
current air delivery mode and
fan speed are also displayed for
about five seconds.

When AUTO is selected, the air
conditioning operation and air
inlet are automatically controlled.
The air conditioning compressor
may run when the outside
temperature is above freezing.
The air inlet will normally be set
to outside air. If it is hot outside,
the air inlet may automatically
switch to the recirculate mode to
help quickly cool down the air
inside the vehicle. The light on
the button comes on in
recirculation.

2. Set the driver and passenger

temperature.

To find your comfort setting, start
with a 23°C (74°F) temperature
setting and allow about
20 minutes for the system to
regulate. Use the driver or
passenger temperature buttons
to adjust the temperature setting
as necessary. If a temperature
setting of 15°C (60°F) is chosen,
the system remains at the
maximum cooling setting. If a
temperature setting of 32°C
(90°F) is chosen, the system
remains at the maximum heat
setting. Choosing either
maximum setting will not cause
the vehicle to heat or cool any
faster.

Do not cover the solar sensor
located on the top of the instrument
panel near the windshield. This
sensor regulates air temperature
based on sun load. For more
information on the solar sensor, see

“

Sensors

”

later in this section.

To avoid blowing cold air in cold
weather, the system delays turning
the fan on until warm air is
available. The length of delay
depends on the engine coolant
temperature. Pressing the fan
switch overrides this delay and
changes the fan to a selected
speed.

Manual Operation

D C

(Fan Control):

Press these

buttons to increase or decrease the
fan speed.

Pressing either fan button while in
automatic control places the fan
under manual control. The fan
setting remains displayed and the
AUTO light turns off. The air
delivery mode remains under
automatic control.

«
...
293
294
295
296
297
...
»

Summary of Contents for silverado 2012

































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for silverado 2012

Brand: U.S. General Pages: 5

Brand: JAC Pages: 70

Brand: UnderCover Pages: 16

Brand: iDataLink Pages: 9

Brand: Raven Pages: 24

Brand: Weather Guard Pages: 4

Brand: JASTEC Pages: 12

Brand: Uebler Pages: 18

Brand: APEXi Pages: 18

Brand: Prorack Pages: 15

CHASSIS CAB 3500 2017

Brand: RAM Pages: 16

Brand: FORM FIT Pages: 2

Brand: Audi Pages: 12

Truck Training Model

Brand: WABCO Pages: 56

Brand: Pyle Pages: 2

Brand: Subaru Pages: 2

Brand: Subaru Pages: 328

Brand: UAZ Pages: 112

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands