Chevrolet silverado 2012 Owner'S Manual Download Page 316 | Manualshive

Page: 316 / 608

background image

Black plate (16,1)

Chevrolet Silverado Owner Manual - 2012

9-16

Driving and Operating

If the Vehicle Is Stuck

Slowly and cautiously spin the
wheels to free the vehicle when
stuck in sand, mud, ice, or snow.
See

“

Rocking Your Vehicle to Get It

Out

”

later in this section.

If the vehicle has a traction system,
it can often help to free a stuck
vehicle. Refer to the vehicle's
traction system in the Index. If stuck
too severely for the traction system
to free the vehicle, turn the traction
system off and use the rocking
method.

{

WARNING

If the vehicle's tires spin at high
speed, they can explode, and you
or others could be injured. The
vehicle can overheat, causing an
engine compartment fire or other
damage. Spin the wheels as little
as possible and avoid going
above 56 km/h (35 mph).

For information about using tire
chains on the vehicle, see

Tire

Chains on page 10

‑

81

.

Rocking Your Vehicle to Get
It Out

Turn the steering wheel left and
right to clear the area around the
front wheels. For four-wheel-drive
vehicles, shift into Four

‐

Wheel High.

For vehicles with StabiliTrak

®

, turn

the traction control part of the
system off. Shift back and forth
between R (Reverse) and a forward
gear, spinning the wheels as little as
possible. To prevent transmission
wear, wait until the wheels stop
spinning before shifting gears.

Release the accelerator pedal while
shifting, and press lightly on the
accelerator pedal when the
transmission is in gear. Slowly
spinning the wheels in the forward
and reverse directions causes a
rocking motion that could free the
vehicle. If that does not get the
vehicle out after a few tries, it might
need to be towed out. Recovery
hooks can be used, if the vehicle
has them. If the vehicle does need
to be towed out, see

Towing the

Vehicle on page 10

‑

101

.

Recovery Hooks

{

WARNING

Never pull on recovery hooks
from the side. The hooks could
break and you and others could
be injured. When using recovery
hooks, always pull the vehicle
straight out.

«
...
314
315
316
317
318
...
»

Summary of Contents for silverado 2012

































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for silverado 2012

Brand: Harken Hoister Pages: 12

Brand: Yamaha Pages: 2

Brand: PAC Pages: 4

Brand: PAC Pages: 4

Brand: PAC Pages: 8

Brand: PAC Pages: 5

Brand: Xblitz Pages: 16

Brand: Taffio Pages: 8

Brand: GMC Pages: 20

Brand: Bestop Pages: 31

2003 Silhouette

Brand: Oldsmobile Pages: 466

Bluetooth Kit3 PLUS

Brand: N-Com Pages: 36

Brand: Vauxhall Pages: 95

Brand: Meritor Pages: 20

SB-J-GCHER2/10W3v2

Brand: Stealthbox Pages: 2

Brand: Pogo Pages: 40

Brand: Beeper Pages: 2

Brand: A-Tach Mounts Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands