Chevrolet silverado 2012 Owner'S Manual Download Page 119 | Manualshive

Page: 119 / 608

background image

Black plate (47,1)

Chevrolet Silverado Owner Manual - 2012

Seats and Restraints

3-47

{

WARNING

Never allow more than one child
to wear the same safety belt. The
safety belt cannot properly spread
the impact forces. In a crash, they
can be crushed together and
seriously injured. A safety belt
must be used by only one person
at a time.

{

WARNING

Never allow a child to wear the
safety belt with the shoulder belt
behind their back. A child can be
seriously injured by not wearing
the lap-shoulder belt properly. In a
crash, the child would not be
restrained by the shoulder belt.
The child could move too far
forward increasing the chance of
head and neck injury. The child
might also slide under the lap
belt. The belt force would then be
applied right on the abdomen.
That could cause serious or fatal
injuries. The shoulder belt should
go over the shoulder and across
the chest.

«
...
117
118
119
120
121
...
»

Summary of Contents for silverado 2012

































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for silverado 2012

Brand: RAM Pages: 292

Brand: RAM Pages: 116

PRIME DESIGN VCR 326

Brand: Safe Fleet Pages: 16

Prime Design VBC PC11

Brand: Safe Fleet Pages: 8

Prime Design AR1418

Brand: Safe Fleet Pages: 4

Brand: JANE Pages: 21

Brand: CITROEN Pages: 52

Brand: Subaru Pages: 34

Brand: BGS technic Pages: 5

Brand: Oldsmobile Pages: 344

Brand: ABL Pages: 66

Brand: Honda Pages: 208

Brand: Thule Pages: 12

Vantage 12 Series

Brand: Ecco Pages: 5

Brand: Cadillac Pages: 34

Brand: SAN HIMA Pages: 7

Peterbilt SmartAir

Brand: Paccar Pages: 58

Brand: Mercedes-Benz Pages: 153

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands