Chevrolet silverado 2012 Owner'S Manual Download Page 70 | Manualshive

Page: 70 / 608

background image

Black plate (24,1)

Chevrolet Silverado Owner Manual - 2012

2-24

Keys, Doors, and Windows

Close:

From the vent, or open

position, press and hold the front of
the switch to close the sunroof.

The sunroof also has a roller
sunshade that can be used to block
the rays of the sun. The roller
sunshade can be manually operated
with the sunroof in an open or
closed position. To open the
sunshade, press and unlatch it, and
roll it back. To close, pull it forward
and latch it into the closed position.

When the sunroof is opened, an air
deflector will automatically raise.
The air deflector will retract when
the sunroof is closed.

Dirt and debris may collect on the
sunroof seal or in the track. This
could cause an issue with sunroof
operation or noise. It could also plug
the water drainage system.
Periodically open the sunroof and
remove any obstacles or loose
debris. Wipe the sunroof seal and
roof sealing area using a clean
cloth, mild soap, and water. Do not
remove grease from the sunroof.

Sunroof (Crew Cab)

A. Open or Close

B. Vent

On vehicles with a sunroof, the
sunroof only operates when the
ignition is in the ACC/ACCESSORY
or ON/RUN or the Retained
Accessory Power (RAP) is active.
See

Retained Accessory Power

(RAP) on page 9

‑

32

for more

information.

Vent:

From the closed position,

press the rear of the passenger side
switch (B) to vent the sunroof.

«
...
68
69
70
71
72
...
»

Summary of Contents for silverado 2012

































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for silverado 2012

Brand: Alpine Pages: 2

Brand: Whispbar Pages: 15

For 1985-1992 GM Cars and Trucks 17933

Brand: Edelbrock Pages: 4

Porsche 911 GT3 R

Brand: iRacing Pages: 25

Brand: CALIMA Pages: 9

Brand: JKS Pages: 3

Tata Indigo Diesel

Brand: TATA Motors Pages: 190

Prime Design HBR-E-FT33B

Brand: Safe Fleet Pages: 12

Brand: Paser Pages: 2

Brand: Xblitz Pages: 56

Brand: Roadmaster Pages: 4

Brand: Kleinn Pages: 8

Brand: Acura Pages: 19

Brand: Ford Pages: 325

Brand: Reliant Pages: 116

Brand: Audi Pages: 4

Brand: Thule Pages: 15

Brand: ACV Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands