Chevrolet silverado 2012 Owner'S Manual Download Page 146 | Manualshive

Page: 146 / 608

background image

Black plate (74,1)

Chevrolet Silverado Owner Manual - 2012

3-74

Seats and Restraints

6. To tighten the belt, push down

on the child restraint, pull the
shoulder portion of the belt to
tighten the lap portion of the belt,
and feed the shoulder belt back
into the retractor. When installing
a forward-facing child restraint, it
may be helpful to use your knee
to push down on the child
restraint as you tighten the belt.

Try to pull the belt out of the
retractor to make sure the
retractor is locked. If the
retractor is not locked, repeat
Steps 5 and 6.

7. If your child restraint has a top

tether, follow the child restraint
manufacturer's instructions
regarding the use of the top
tether. See

Lower Anchors and

Tethers for Children (LATCH
System) on page 3

‑

54

for more

information.

8. Before placing a child in the

child restraint, make sure it is
securely held in place. To check,
grasp the child restraint at the
safety belt path and attempt to
move it side to side and back
and forth. When the child
restraint is properly installed,
there should be no more than
2.5 cm (1 in) of movement.

To remove the child restraint,
unbuckle the vehicle safety belt and
let it return to the stowed position.
If the top tether is attached to a top
tether anchor, disconnect it.

«
...
144
145
146
147
148
...
»

Summary of Contents for silverado 2012

































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for silverado 2012

Brand: Kargo Master Pages: 6

MCL-7000 Series

Brand: Dakota Digital Pages: 2

Brand: Volvo Pages: 284

Brand: Gator Pages: 2

Bluetooth Phone System 2010

Brand: Kia Pages: 16

Brand: Porsche Pages: 146

Brand: Edelbrock Pages: 2

Brand: Hudson Pages: 77

Brand: Motoalliance Pages: 4

Brand: iSimple Pages: 8

Brand: Mitsubishi Pages: 57

Brand: Easee Pages: 21

PRO-FLO XT 3527

Brand: Edelbrock Pages: 39

Brand: Buick Pages: 58

Brand: Directed Pages: 24

1995 Sedan De Ville

Brand: Cadillac Pages: 403

Brand: Blueant Pages: 53

Brand: DieHard Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands