Chevrolet silverado 2012 Owner'S Manual Download Page 540 | Manualshive

Page: 540 / 608

background image

Black plate (4,1)

Chevrolet Silverado Owner Manual - 2012

11-4

Service and Maintenance

Engine Oil Change

When the CHANGE ENGINE OIL
SOON message displays, have the
engine oil and filter changed within
the next 1 000 km/600 mi. If driven
under the best conditions, the
engine oil life system might not
indicate the need for vehicle service
for more than a year. The engine oil
and filter must be changed at least
once a year and the oil life system
must be reset. Your trained dealer
technician can perform this work.
If the engine oil life system is reset
accidentally, service the vehicle
within 5 000 km/3,000 mi since the
last service. Reset the oil life
system when the oil is changed.
See

Engine Oil Life System on

page 10

‑

10

.

Tire Rotation and Required
Services Every 12 000 km/
7,500 mi

Rotate the tires, if recommended for
the vehicle, and perform the
following services. See

Tire

Rotation on page 10

‑

72

.

.

Check engine oil level and oil
life percentage. If needed,
change engine oil and filter, and
reset oil life system. See

Engine

Oil on page 10

‑

7

and

Engine Oil

Life System on page 10

‑

10

.

.

Check engine coolant level. See

Engine Coolant on page 10

‑

21

.

.

Check windshield washer fluid
level. See

Washer Fluid on

page 10

‑

29

.

.

Visually inspect windshield wiper
blades for wear, cracking,
or contamination. See

Exterior

Care on page 10

‑

106

. Replace

worn or damaged wiper blades.
See

Wiper Blade Replacement

on page 10

‑

40

.

.

Check tire inflation pressures.
See

Tire Pressure on

page 10

‑

65

.

.

Inspect tire wear. See

Tire

Inspection on page 10

‑

71

.

.

Visually check for fluid leaks.

.

Inspect engine air cleaner filter.
See

Engine Air Cleaner/Filter on

page 10

‑

18

.

.

Inspect brake system.

«
...
538
539
540
541
542
...
»

Summary of Contents for silverado 2012

































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for silverado 2012

Brand: GMC Pages: 140

Brand: Ecco Pages: 9

Brand: Ecco Pages: 9

Brand: TATA Motors Pages: 164

Brand: HALE Pages: 44

Brand: Conrad Pages: 26

2003 Thunderbird

Brand: Ford Pages: 200

Multiple G9F18 AU000

Brand: Genesis Pages: 3

Brand: Jeep Pages: 16

Brand: Audi Pages: 4

Brand: Skoda Pages: 165

Brand: Sanitas Pages: 36

Brand: Xingyun Pages: 74

Brand: Subaru Pages: 16

Omni-Bike Sport Ducato

Brand: OMNISTOR Pages: 5

Brand: iSimple Pages: 8

Brand: VP Autoparts Pages: 2

Brand: BabySafe Pages: 43

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands