Chevrolet silverado 2012 Owner'S Manual Download Page 492 | Manualshive

Page: 492 / 608

background image

Black plate (68,1)

Chevrolet Silverado Owner Manual - 2012

10-68

Vehicle Care

When the malfunction indicator is
illuminated, the system may not be
able to detect or signal low tire
pressure as intended. TPMS
malfunctions may occur for a variety
of reasons, including the installation
of replacement or alternate tires or
wheels on the vehicle that prevent
the TPMS from functioning properly.
Always check the TPMS malfunction
telltale after replacing one or more
tires or wheels on your vehicle to
ensure that the replacement or
alternate tires and wheels allow the
TPMS to continue to function
properly.

See

Tire Pressure Monitor

Operation on page 10

‑

68

for

additional information.

Federal Communications
Commission (FCC) Rules and
with Industry Canada
Standards

See

Radio Frequency Statement on

page 13

‑

23

for information

regarding Part 15 of the Federal
Communications Commission (FCC)
Rules and with Industry Canada
Standards RSS-GEN/210/220/310.

Tire Pressure Monitor
Operation

This vehicle may have a Tire
Pressure Monitor System (TPMS).
The TPMS is designed to warn the
driver when a low tire pressure
condition exists. TPMS sensors are
mounted onto each tire and wheel
assembly, excluding the spare tire
and wheel assembly. The TPMS
sensors monitor the air pressure in
the tires and transmit the tire
pressure readings to a receiver
located in the vehicle.

When a low tire pressure condition
is detected, the TPMS illuminates
the low tire pressure warning light
located on the instrument cluster.
If the warning light comes on, stop
as soon as possible and inflate the
tires to the recommended pressure
shown on the Tire and Loading
Information label. See

Vehicle Load

Limits on page 9

‑

17

.

A message to check the pressure in
a specific tire displays in the Driver
Information Center (DIC). The low
tire pressure warning light and the
DIC warning message come on at
each ignition cycle until the tires are
inflated to the correct inflation
pressure. If the vehicle has DIC
buttons, tire pressure levels can be
viewed. For additional information
and details about the DIC operation

«
...
490
491
492
493
494
...
»

Summary of Contents for silverado 2012

































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for silverado 2012

Brand: JETBAG Pages: 44

Brand: Subaru Pages: 99

MCL-7000 Series

Brand: Dakota Digital Pages: 2

Brand: Volvo Pages: 284

Brand: Ranger design Pages: 22

Quantum hardcoated N30216

Brand: National Cycle Pages: 3

Brand: Skoda Pages: 165

Ford 4” UNI-CAM

Brand: Nav TV Pages: 6

2007 9-3 Remote Starter

Brand: Saab Pages: 304

Brand: EUFAB Pages: 16

Brand: Qeedon Pages: 2

Brand: Saab Pages: 15

Brand: Ferve Pages: 28

Brand: Vauxhall Pages: 95

Brand: MBRP Pages: 5

Brand: Green Valley Pages: 17

Powerbuilt 648601

Brand: AllTrade Pages: 3

SportQuest Series

Brand: Perrycraft Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands