Chevrolet silverado 2012 Owner'S Manual Download Page 410 | Manualshive

Page: 410 / 608

background image

Black plate (110,1)

Chevrolet Silverado Owner Manual - 2012

9-110

Driving and Operating

If charging a remote (non-vehicle)
battery, press the Tow/Haul Mode
button, if equipped, located at the
end of the shift lever. This will boost
the vehicle system voltage and
properly charge the battery. If the
trailer is too light for Tow/Haul
Mode, or the vehicle is not equipped
with Tow/Haul, turn on the
headlamps as a second way to
boost the vehicle system and
charge the battery.

Camper/Fifth-Wheel Trailer Wiring
Package

The seven-wire camper harness is
located under the front edge of the
pickup box on the driver side of the
vehicle, attached to the frame
bracket. A connector must be added
to the wiring harness which
connects to the camper.

The harness contains the following
camper/trailer circuits:

.

Yellow: Left Stop/Turn Signal

.

Dark Green: Right Stop/Turn
Signal

.

Brown: Taillamps

.

White: Ground

.

Light Green: Back-up Lamps

.

Red: Battery Feed

.

Dark Blue: Trailer Brake

If the vehicle is equipped with the

“

Heavy-Duty Trailering

”

option,

please refer to

“

Heavy-Duty Trailer

Wiring Package

”

earlier in this

section.

When the camper-wiring harness is
ordered without the heavy-duty
trailering package, a seven-wire
harness with a seven-pin connector
is located at the rear of the vehicle
and is tied to the vehicle's frame.

«
...
408
409
410
411
412
...
»

Summary of Contents for silverado 2012

































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for silverado 2012

Brand: EAL Pages: 4

Brand: FABBRI PORTATUTTO Pages: 2

Brand: Porsche Pages: 192

1306 RAPID SYSTEM

Brand: Thule Pages: 8

STRONGARM RVR303

Brand: Blue Giant Pages: 48

Brand: Audi Pages: 9

Brand: Belkin Pages: 4

Brand: Edelbrock Pages: 1

Brand: FORM FIT Pages: 2

Brand: U.S. General Pages: 4

Brand: Hella Pages: 21

Brand: Kia Pages: 51

Brand: EUFAB Pages: 16

Brand: rough country Pages: 4

Brand: Mercedes-Benz Pages: 398

Brand: Dometic Pages: 24

F-250 Super Duty 2022

Brand: Ford Pages: 740

Brand: Oldsmobile Pages: 248

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands