Chevrolet silverado 2012 Owner'S Manual Download Page 181 | Manualshive

Page: 181 / 608

background image

Black plate (33,1)

Chevrolet Silverado Owner Manual - 2012

Instruments and Controls

5-33

Front Fog Lamp Light

For vehicles with fog lamps, this
light comes on when the fog lamps
are on.

The light goes out when the fog
lamps are turned off. See

Fog

Lamps on page 6

‑

7

for more

information.

Cruise Control Light

For vehicles equipped with cruise
control, this light comes on
whenever the cruise control is set.

The light goes out when the cruise
control is turned off. See

Cruise

Control on page 9

‑

69

for more

information.

Information Displays

Driver Information
Center (DIC)

The vehicle has a Driver Information
Center (DIC).

The DIC displays information about
this vehicle. It also displays warning
messages if a system problem is
detected.

All messages will appear in
the DIC display located below the
tachometer in the instrument panel
cluster.

The DIC comes on when the ignition
is on. After a short delay, the DIC
will display the information that was
last displayed before the engine
was turned off.

«
...
179
180
181
182
183
...
»

Summary of Contents for silverado 2012

































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for silverado 2012

Brand: KC HiLiTES Pages: 4

Brand: cam Pages: 28

Brand: Porsche Pages: 144

Brand: Calix Pages: 5

Wallbox eM4 Single

Brand: ABL Pages: 68

Brand: minnid Pages: 44

Brand: Whipple Pages: 3

STEALTH POWER RBP-216-SP

Brand: RBP Pages: 16

STREET SUPER SHIFTER

Brand: HURST Pages: 2

Brand: Rati Pages: 2

Ferrari 360 Map Carbon Light

Brand: MAcarbon Pages: 4

Brand: Nuna Pages: 17

Brand: METRON Pages: 4

Brand: Metra Electronics Pages: 2

Brand: Brink Pages: 26

Brand: Brigade Pages: 12

Brand: SIXTOL Pages: 32

SHERPA SADDLE BAG JL

Brand: Overland Outfitters Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands