Chevrolet silverado 2012 Owner'S Manual Download Page 23 | Manualshive

Page: 23 / 608

background image

Black plate (17,1)

Chevrolet Silverado Owner Manual - 2012

In Brief

1-17

Safety Belts

Refer to the following sections for
important information on how to use
safety belts properly.

.

Safety Belts on page 3

‑

14

.

.

How to Wear Safety Belts
Properly on page 3

‑

15

.

.

Lap-Shoulder Belt on page 3

‑

17

.

.

Lower Anchors and Tethers for
Children (LATCH System) on
page 3

‑

54

.

Passenger Sensing
System

The passenger sensing system,
if equipped, turns off the front
outboard passenger frontal airbag
under certain conditions. No other
airbag is affected by the passenger
sensing system.

If the vehicle has one of the
indicators pictured in the following
illustrations, then the vehicle has a
passenger sensing system for the
right front passenger position unless
there is an airbag off switch located
in the glove box.

If there is an airbag off switch, the
vehicle does not have a passenger
sensing system. See

Airbag On-Off

Switch on page 3

‑

33

for more

information.

The passenger airbag status
indicator will be visible on the
overhead console when the vehicle
is started.

United States

Canada and Mexico

See

Passenger Sensing System on

page 3

‑

37

for important information.

«
...
21
22
23
24
25
...
»

Summary of Contents for silverado 2012

































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for silverado 2012

Brand: Warrior Products Pages: 2

Brand: Mobis Pages: 16

Brand: Subaru Pages: 216

autoSteady AS101

Brand: Enduro Pages: 48

Brand: Caltrend Pages: 2

Brand: Advanced ICE Pages: 4

Brand: Hank Pages: 2

Brand: Skoda Pages: 281

Brand: TEINHOF Pages: 2

Brand: rough country Pages: 4

Brand: Yakima Pages: 12

Brand: Cadillac Pages: 529

Brand: Toro Pages: 16

Brand: Honda Pages: 268

LED Dominator TAM83S2

Brand: Whelen Engineering Company Pages: 2

Brand: AutoLoc Pages: 6

C-Max Energi 2014

Brand: Ford Pages: 10

Brand: Gacell Pages: 25

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands